714930
13
Zoom out
Zoom in
Previous page
1/25
Next page
POWXG1022 EN
Copyright © 2016 VARO P a g e | 13 www.varo.com
Let the engine run for 10 seconds to warm up. Press the trigger (H) and put it into idle
(Fig. 9e).
If the engine does not start up, repeat the above steps.
10.3 Re-starting a warm engine
Make sure the on/off switch is in the “I” position.
Pull the starter rope rapidly 2 times. The engine should start.
10.4 To stop engine (Fig. 9f)
Release trigger and allow engine to return to idle speed.
Push the I/O (on/off) switch to o (off) to stop engine.
Note: for emergency stopping, simply activate chain brake and switch the
I/O (on/off) switch to O (off).
10.5 Chain brake operational test
Test the chain brake periodically to ensure proper function.
Perform a chain brake test prior to initial cutting, following extensive cutting, and definitely
following any chain brake service.
Test chain brake as follows:
Place saw on a clear, firm, flat surface.
Start engine.
Grasp the rear handle (A) with your right hand (Fig. 10).
With your left hand, hold the front handle (B) [not chain brake lever (C)] firmly (Fig. 10).
Squeeze the throttle trigger to 1/3 throttle, then immediately activate the chain brake lever
(C) (Fig. 10).
Warning: activate the chain brake slowly and deliberately. Keep the chain
from touching anything; don t let the saw tip forward.
Chain should stop abruptly. When it does, immediately release the throttle trigger.
Warning: if chain does not stop, turn engine off and take your unit to the
nearest authorized service centre for service.
If chain brake functions properly, turn the engine off and return the chain brake to the
disengaged position.
Warning: if chain does not stop, turn engine off and take your unit to the
nearest authorized service centre for service.
10.6 Saw chain / bar lubrication
Adequate lubrication of the saw chain is essential at all times to minimize friction with the
guide bar. Never starve the bar and chain of oil. Running the saw with too little oil will
decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and cause
excessive wear of bar from overheating. Too little oil is evidenced by smoke, bar discoloration
or pitch build-up. To ensure the bar and chain receive oil, only use the original style bar with
the oil passage hole (A) as illustrated above (Fig. 3a).
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG1022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG1022 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG1022

Powerplus POWXG1022 User Manual - German - 29 pages

Powerplus POWXG1022 User Manual - Dutch - 26 pages

Powerplus POWXG1022 User Manual - French - 28 pages

Powerplus POWXG1022 User Manual - Italian - 27 pages

Powerplus POWXG1022 User Manual - Spanish - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info