517143
17
Zoom out
Zoom in
Previous page
1/22
Next page
POWXG1018 EN
Copyright © 2015 VARO P a g e | 17 www.varo.com
To lubricate sprocket tip:
Warning: wear heavy duty work gloves when handling the bar and chain.
Press the stop switch down.
Note: it is not necessary to remove the saw chain to lubricate the guide bar
sprocket tip. Lubrication can be done on the job.
21. Clean the guide bar sprocket tip.
Using the lube gun (optional), insert needle nose into the lubrication hole and inject grease
until it appears at outside edge of sprocket tip (fig. 20).
Rotate saw chain by hand. Repeat lubrication procedure until the entire sprocket tip has
been greased.
12.3 Guide bar maintenance:
Most guide bar problems can be prevented merely by keeping the chain saw well maintained.
Insufficient guide bar lubrication and operating the saw with chain that is too tight will
contribute to rapid bar wear. To help minimize bar wear, the following guide bar maintenance
procedures are recommended.
Warning: always wear protective gloves during maintenance operations. Do
not carry out maintenance when the engine is hot.
12.4 Chain sharpening:
Chain sharpening requires special tools to ensure that cutters are sharpened at the correct
angle and depth. For the inexperienced chain saw user, we recommend that the saw chain be
professionally sharpened by the nearest professional service center. For non-experienced
users of the chain saw, we recommend to have the chain sharpened by a specialist in any
authorized service.
Warning: when having wrong sharpened chain, there may occur a higher
danger of kickback.
To sharpen the saw chain, use the suitable sharpening tools:
round chain file
file leading
chain measuring calibre.
These tools can be bought in any specialsed stores.
To gain well shaped sawdust particles, use sharp chain. If there appears wooden powder,
you must sharpen the saw chain.
Warning: all cutting teeth must be similarly long. Different length of the
teeth can cause rough run of the chain or its rupture, as well.
Minimum length of the teeth must be 4mm. If they are shorter, remove the saw chain.
Angles, which the teeth are under, must be followed.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG1018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG1018 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG1018

Powerplus POWXG1018 User Manual - German - 28 pages

Powerplus POWXG1018 User Manual - Dutch - 28 pages

Powerplus POWXG1018 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info