675265
12
Zoom out
Zoom in
Previous page
1/16
Next page
POWX516 EN
Copyright © 2015 VARO P a g e | 12 www.varo.com
Check the oil drain plug, gasket, oil filler cap and O-ring. If damaged replace.
Reinstall the oil drain bolt.
Refill engine oil to the upper level. (Fig. 7)
12.4 Air filter (Fig. 8)
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction,
service the air cleaner regularly. Service more frequently when operating the generator in
extremely dusty areas.
1. Unsnap the air cleaner cover clips, remove the air cleaner cover and remove the element.
2. Wash the air cleaner element in a solution of household detergent and warm water, then
rinse thoroughly or wash in non-flammable or high flashpoint solvent. Allow the air
cleaner element to dry thoroughly.
3. Soak the air cleaner element in clean engine oil and squeeze out the excess oil. The
engine will smoke during initial startup if too much oil is left in the air cleaner element.
4. Reinstall the air cleaner element and the cover.
CAUTION: The engine should never run without the air filter element;
excessive piston and/or cylinder wear will result.
12.5 Fuel sediment cup cleaning (Fig. 9)
The sediment cup prevents dirt or water which may be in the fuel tank from entering the
carburetor. If the engine has not been running for a long time, the sediment cup should be
cleaned.
1. Turn the fuel valve lever to the OFF position. Remove the sediment cup, O-ring and filter.
2. Clean the sediment cup, O-ring and filter in nonflammable or high flash point solvent.
3. Reinstall the filter, O-ring and sediment cup.
4. Turn the fuel valve lever ON and check for leaks.
12.6 Cleaning / adjusting / replacing spark plug
Easy starting and optimum running of the engine is only possible when the spark plug is clean
and correctly mounted.
Remove the spark plug cable from the spark plug.
Place spark plug key on the spark plug and unscrew it.
The spark plug should be light to dark brown (Standard electrode color: Tan Color). A
black spark plug indicates that the mixture is too rich (choke used for too long, frequent
running for short periods).
Clean the spark plug with a spark plug brush. (This has copper bristles - do not use a steel
brush, otherwise you will damage the spark plug!)
Check the gap between the electrodes with a gauge. It should be between 0.6 and 0.8
mm. If necessary, adjust the gap by carefully bending the electrode. If the gap is too wide,
the ignition spark is too weak or may be completely absent. If the gap is too small, the
electrode becomes burnt, and the plug will not spark reliably.
If the electrode is burnt, or the ceramic insulator is damaged, replace the spark plug. Use
spark plugs with the same charasteristics.
Re-place the spark plug in its housing and screw it tight by hand. The spark plug must
allow itself to be screwed in very easily. - otherwise unscrew again, check the thread for
foreign bodies and screw in again (straight).
Use a plug spanner to tighten the hand-tightened spark plug by a further quarter revolution
and no more, otherwise the thread will be damaged.
Re-place the spark plug cable on the spark plug and ensure that it is seated tightly.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX516 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX516 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX516

Powerplus POWX516 User Manual - German - 17 pages

Powerplus POWX516 User Manual - Dutch - 16 pages

Powerplus POWX516 User Manual - French - 18 pages

Powerplus POWX516 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info