675263
7
Zoom out
Zoom in
Previous page
1/16
Next page
POWX513 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
8.3 Assembly of handle clamp and handle
Slide the clamp over the cross bar until the holes in the handle correspond with the holes
in the cross bar. Fix the clamp with the supplied M6x60 bolt and nut. (Fig 1)
Attach the holder of the handle on the top tube with two supplied bolts M8x35 and M8 nuts
in the foreseen holes. Please note that the open side of the holder should face down.
Mount the handle in the holder with the supplied spindle bolt and M6 nut. (Fig 2)
8.4 Assembly wheels
Slide every wheel over an axle. Put a cotter pin in the bore of every wheel axle and bend the
ends of the cotter pin to fix.
9 CONTROL FUNCTIONS
9.1 Recoil starter
To start the engine, pull the starter grip lightly until resistance is felt, then pull briskly.
Do not allow the starter grip to snap back against the engine. Return it
gently to prevent damage to the starter. When starting the engine by recoil
starter, set the key switch at the ON position and pull the starter handle.
9.2 Fuel valve lever
The fuel valve is located between the fuel tank and carburetor. When the valve lever is in the
ON position, fuel is allowed to flow from the fuel tank to the carburetor. Be sure to return the
fuel valve lever to the OFF position after stopping the engine.
9.3 Choke rod
The choke is used to provide an enriched fuel mixture when starting a cold engine. It can be
opened and closed by operating the choke rod manually. Pull the rod out toward CLOSED to
enrich the mixture for cold starting.
9.4 Ground terminal
The generator ground terminal is connected to the frame of the generator, the metal non-
current-carrying parts of the generator and the ground terminals of each receptacle
9.5 DC circuit breaker
The DC circuit protector automatically shuts off the DC battery charging circuit when the DC
charging circuit is overloaded, when there is a problem with the battery or when the
connections between the battery and the generator are improper.
9.6 Oil alert system
The oil alert system is designed to prevent engine damage caused by an insufficient amount
of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the oil
alert system will automatically stop the engine (the engine switch will remain in the ON
position). The oil alert system should not take the place of checking the oil level before each
use.
If the engine stops and will not restart, check the engine oil level before troubleshooting in
other areas.
9.7 AC circuit breaker
The AC circuit breaker will automatically switch OFF if there is a short circuit or a significant
overload of the generator at the receptacle. If the AC circuit breaker is switched OFF
automatically, check that the appliance is working properly and does not exceed the rated laod
capacity of the circuit before switching the AC circuit breaker ON again. The AC circuit breaker
may be used to switch the generator power ON or OFF.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX513 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX513 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX513

Powerplus POWX513 User Manual - German - 17 pages

Powerplus POWX513 User Manual - Dutch - 16 pages

Powerplus POWX513 User Manual - French - 17 pages

Powerplus POWX513 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info