582375
8
Zoom out
Zoom in
Previous page
1/13
Next page
POWX204 EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
7. Align laterally so that no element protrudes to the right or left.
8. Once installed you should make sure that the cutters are sitting properly in their sites. To
do so, use the blade-adjusting device provided with the appliance.
9. Re-tighten the five screws of the spacer holder
10. To install new cutters: proceed as above but use new cutters.
7.7 Using the blade adjuster (Fig I)
Position the adjusting tool on the surface of the outfeed table
Make sure the adjusting device is flat on the table surface.
Apply pressure to one side of the tool on the cutter until it is positioned at the desired
depth.
!! Handle the blades carefully to avoid risk of accidents. Do not touch the
blades with your fingers.
7.8 Installing chip extractors
ATTENTION !!!!!!
This machine is delivered with chip extractors. These extractors have slots that
deactivate the cutter safety system. If the extractor (varies according to use, i.e., either
as jointer or planer) is not in place or is placed incorrectly it is impossible to use the
appliance.
A In jointer mode (Fig J) :
a : Slots that deactivate the safety system and allow the appliance to start
b : Slots for attaching the chip extractor to the body of the appliance
Chip extractor for using the appliance in jointer mode.
To install the chip extractor in jointer mode you must:
(Fig K)
1. Adjust the work table to low position
2. Insert the chip extractor to a good angle below the table of the jointer (as indicated in Fig
K)
3. Locate each slot described in the diagram above in order to insert them in the openings
provided.
4. Make sure the extractors are firmly in place.
(Fig L)
5. Return the worktable back to high position using the height adjusting knob until the
extractor and the slots that deactivate the safety system touch the contact.
6. This operation is indispensable for starting up the appliance.
7. The appliance is now running. You may use it in accordance with the instructions for use.
B In planing mode :
Chip extractor for use of the appliance in planer mode.
(Fig M)
a : Clamping screw
b : Contact
To install the chip extractor in planing mode you must remove the protective parallel guide.
Localise the clamping screw and align this screw with the opening (as shown in fig N).
After alignment turn the clamp screw until it is completely blocked (Fig. O).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX204 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX204 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX204

Powerplus POWX204 User Manual - German - 15 pages

Powerplus POWX204 User Manual - Dutch - 14 pages

Powerplus POWX204 User Manual - French - 15 pages

Powerplus POWX204 Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info