Manual Powerplus POWX1735 (page 6 of 10) (English)

480944

Zoom out

Zoom in

1/10

POWX1735 EN

6.3 Things you should know

 To avoid overheating of the electric motor, this compressor is designed for intermittent

operation as indicated on the technical dataplate. In the case of overheating, the thermal

cutout of the motor trips, automatically cutting off power when the temperature is too high.

The motor restarts automatically when normal temperature conditions are restored.

 To facilitate restart of the compressor, in addition to the operations indicated, it is

important to return the button of the pressure switch to the OFF position and then to ON

again. (Figures 2-3-4)

 Single-phase versionns are fitted with a pressure switch equipped with a delayed closing

air discharge valve which facilitates start-up of the motor. Therefore venting of air from this

valve for a few seconds with the receiver empty is normal.

 All the compressors are fitted with a safety valve that is tripped in the case of

malfunctioning of the pressure switch in order to assure machine safety.

 When fitting a tool, the flow of air in output must be switched off.

 When using compressed air, you must know and comply with the safety precautions to be

adopted for each type of application (inflation, pneumatic tools, painting, washing with

water-based detergents onlt, etc.).

7 START-UP AND USE

 Fit the wheels and foot (or the suckers according to model) following the instructions

provided in the packaging.

 Check for correspondence between the compressor plate data with the actual

specifications of the electrical system. A variation of ± 10% with respect of the rated value

allowed.

 Insert the plug of the power cable in a suitable socket (fig.6) checking the the button of the

pressure switch located on the compressor is in the OFF “O” position.

 For lubricated models, check the oil level using the rod included in the oil fuel plug (figures

7a-7b-7c) and if necessary top up.

 At this point, the compressor is ready for use.

 Operating on the switch of the pressure switch (fig. 3), the compressor starts, pumping air

into the receiver through the delivery pipe.

 When the upper calibration value (set by the manufacturer) has been reached, the

compressor stops, venting the excess air present in the head and in the delivery pipe

through a valve located under the pressure switch.

This facilitates subsequent restart due to the absence of pressure in the head. When air is

used, the compressor restarts automatically when the lower calibration value is reached

(2bar between upper and lower).

 The pressure in the receiver can be checked on the gauge provided (fig.8).

 The compressor continues to operate according to this automatic cycle until the switch of

the pressure switch is turned.

 Always wait at least 10 seconds from when the compressor has been switched off before

restarting this.

 All compressors are fitted with a pressure reducer. Operating on the knob with the tap

open (pulling it up and turning it in a clockwise direction to increase the pressure and in a

counterclockwise direction to reduce this (fig 9), air pressure can be regulated so as to

optimize use of pneumatic tools. After setting the value required, push the knob to fasten

this (fig. 9B). on some versions, the ring-nut underneath must be tightened to fasten the

knob (figures 9c-9d)

 The value set can be checked on the gauge.

 Please check that the air consumption and the maximum working pressure of the

pneumatic tool to be used are compatible with the pressure set on the pressure regulator

and with the amount of air supplied by the compressor.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1735 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1735

Powerplus POWX1735 User Manual - German - 11 pages

Powerplus POWX1735 User Manual - Dutch - 11 pages

Powerplus POWX1735 User Manual - French - 11 pages

Powerplus POWX1735 Additional guide - All languages - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX1735 Manual

Product: