645074
9
Zoom out
Zoom in
Previous page
1/12
Next page
POWX1425 EN
Copyright © 2016 VARO P a g e | 9 www.varo.com
Once the cut has been finished, lift the tool from the work surface before switching off. If a
lot of dust has been created, keep switched on for a few seconds extra to allow the dust to
clear from within the tool.
WARNING! If any of the following events occur during normal operation, the
power supply should be shut off at once and tool thoroughly inspected by a
qualified person and repaired if necessary:
The rotating parts get stuck or speed drops abnormally low.
The tool shakes abnormally accompanied by some unusual noise.
The motor housing gets abnormally hot.
Heavy sparks occur around the motor area.
9.5 Pocket Cut
Install a saw blade suitable for the material you are about to saw. (see chapter 2.
Description Accessories). Set the depth of cut, plug in the mains supply and then place
the base plate (14) onto the work surface. Ensure that the front indication mark on the
base plate aligns with the start line.
Switch on the tool and wait for a moment until the blade reaches full speed. Next, plunge
the blade slowly and gently, but firmly into the material. Then push the tool forwards along
the line to be cut. (Never draw the tool backwards)
Once the finish line has been reached, lift the tool from the work surface before switching
off. If a lot of dust has been created, keep switched on for extra few seconds to allow the
dust being discharged from the tool.
10 CUT-OUTS
10.1 Cutting out tips:
If the cut is to be covered, for example by a vent cover, the corners can be overlapped to
ensure that the waste material is completely detached. (Fig. 9)
If the cut out is to be seen, do not overlap the corners. In this circumstance, as the cutting
blade is circular, the waste material will not be fully detached. The corners will therefore,
require finishing with a knife. If the material is thin and the back surface unimportant, the
waste material can just be pushed out. (Fig. 10)
Where there is access to the back surface of the material to be cut, the cut out can be
marked out with an over cutting allowance. The cut is then made from the back surface to
ensure perfect corners on the front surface. (Fig. 11)
10.2 Cutting particularly Tough or Abrasive Materials
10.2.1 Sheet metal:
Only use a blade specifically designed for this purpose.
Always set the depth adjustment to at least 1 mm deeper than the material thickness to
avoid the blade riding up over the surface. Scrap material is required underneath the work
surface.
Remove burrs and rust as these impede the feed across the material.
Thick beeswax (furniture polish) applied to the base plate of the tool makes metal cutting
easier. (the base plate will slide easier over the work piece)
Only suitable for cutting brass, copper, lead, aluminium or galvanised mild steel.
Every 2 minutes of metal cutting should be followed by a rest of at least 3 minutes.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1425 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1425 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1425

Powerplus POWX1425 User Manual - German - 14 pages

Powerplus POWX1425 User Manual - Dutch - 14 pages

Powerplus POWX1425 User Manual - French - 13 pages

Powerplus POWX1425 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info