645073
6
Zoom out
Zoom in
Previous page
1/9
Next page
POWX1420 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
7.2 Depth adjustment (Fig. 7)
Loosen the cutting depth setting clamp (9) by lifting the lock lever.
Hold the base plate (14) flat against the body of the work piece and lift the body of the saw
until the blade is at the right depth.
Tighten the depth locking lever.
7.3 Angle adjustment (Fig. 8)
Loosen the lock lever knob for angle adjustment (11).
Adjust the base plate (14)(to the desired angle between 0° to 45°.
Tighten the lock lever knob for angle adjustment (11).
Note: for best cutting results, always ensure that saw blade protrudes no
more than 3 mm below the bottom surface of the workpiece.
7.4 General cut
Mark a cutting line on the workpiece.
Rest the front part of the shoe flat on the workpiece surface with the blade not making any
contact with the workpiece.
Switch on the tool and allow it to reach its full speed.
Align the saw blade with the cutting line on the workpiece, gently push the saw forward.
Never force the saw but maintain a light and continuous pressure when completing the
cut. Switch off the tool only after the tool is completely away from the workpiece When the
cutting is interrupted, resume the cut by allowing the blade to reach full speed and then re-
entering the cut slowly
When cutting across the grain, the fibres of the wood will have a tendency to lift and tear,
moving the saw slowly to minimize this effect.
Note: there are two notches on the front edge of the shoe as an aid for
alignment. When making a 45° bevel cut, just align the left notch marked
with 45° with the cutting line on the workpiece. For a straight 90° cut, align
the right notch marked with with the cutting line on the workpiece. For
precise cutting, always make a trial cut before carrying out operation
7.5 Pocket cutting
Disconnect the plug from the power supply before making any adjustments. Set the depth
adjustment based on the thickness of the line drawing for the cut .raise the lower guard by
using the lift lever.
With the blade barely above the material to be cut, start the saw and allow the blade to
come to full speed. Gradually lower the blade unto the material to be cut using the front
end of the shoe as a pivot point. When the blade starts cutting, release the lower guard.
When the shoe is resting flat on the surface being cut, proceed cutting in a forward
direction to the end of the cut. Allow the blade to come to a full stop before removing it
from the cut. Never pull the saw backward since the blade will climb out of the cut and
kickback will occur. Turn the saw around and finish the cut in a normal manner, sawing
forward. Use a jigsaw or a hand saw to finish the cut in the corners, if required.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1420 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1420

Powerplus POWX1420 User Manual - German - 10 pages

Powerplus POWX1420 User Manual - Dutch - 10 pages

Powerplus POWX1420 User Manual - French - 10 pages

Powerplus POWX1420 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info