645079
8
Zoom out
Zoom in
Previous page
1/11
Next page
POWX0910 EN
Copyright © 2016 VARO P a g e | 8 www.varo.com
Repeat the procedure at the other side.
CAUTION: Dust may cause respiratory problems. Certain laminated board
materials are carcinogenic. After work, always remove all dust from the
machine.
7.7 Using the dust exhaust connection
The dust exhaustion outlet (14) shall be connecting together with an external vacuum
cleaner to take away the dust in dust cover.
If necessary, place an adapter on the dust exhaust.
8 OPERATION
8.1 Cutting in several operations (Fig. 7)
The length-stop turret (9) can be used to set different depths.
For cutting in depth and in stages, use the length-stop turret (9) as an aid. Using the depth
stop set the desired depth to the lowest depth-stop position on the turret. Rotate the turret so
that the highest point is under the depth stop and execute the first cut. Repeat the cut with the
second-highest setting and finally with the last setting. You can also use two positions if the
desired depth is reached in two operations.
8.2 Switching on and off (Fig. 8-9)
Connect the plug to the power supply.
To switching the tool on, keep the lock-off button (12) depressed and press the ON/OFF
switch trigger (11).
To switching the tool off, release the ON/OFF switch trigger (11).
To adjust the cutting speed, turn the speed control dial (2). Position 1 denotes the lowest
speed. Position 7 denotes the highest speed. Turn the knob to increase or decrease the
speed. The smaller the cutter head, the higher the speed. The larger the cutter head, the
lower the speed. A cutter head which runs too fast causes scorching of the work-piece and
leaves burnt marks.
CAUTION: Do not change the speed when the machine is working under
load.
8.3 Cutting direction
Always observe the safety instructions and applicable regulations.
Always move your router as indicated in below Fig. 10 (outer edges/inner edges).
To prevent the cutter head from jumping and to obtain a good result, carry out exterior
cuts in anticlockwise and interior cuts in clockwise direction.
NOTE: Check that the cutter is correctly installed in the collet.
Place the machine on the workpiece before switching on.
Select the optimal speed using the speed control dial.
Set the cutting depth.
For greater cutting depths it is recommended to make shallow cuts.
Connect a dust cover.
Make sure the locking lever is always locked before switching on.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0910 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0910

Powerplus POWX0910 User Manual - German - 12 pages

Powerplus POWX0910 User Manual - Dutch - 11 pages

Powerplus POWX0910 User Manual - French - 12 pages

Powerplus POWX0910 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info