582665
6
Zoom out
Zoom in
Previous page
1/11
Next page
POWX0682 EN
Copyright © 2014 VARO P a g e | 6 www.varo.com
If the blades come in contact with the work piece before they reach full speed, it could
cause the saw to kickback toward you resulting in serious injury.
7 ASSEMBLY
7.1 Attaching the handle
Screw handle into saw (fig 1).
Use nut to tighten the handle.
7.2 Removing the blades
Be sure to first unplug the electric cord from the electrical outlet and allow
blades to cool before removing the blades.
Push the spindle lock to secure the blade (Fig 2).
Use the blade wrench to unscrew the lock nut (Fig 3).
Remove lock nut from the blade (Fig 4).
Open lower guard of the blade (Fig 5).
Lift up and remove “Face B” blade (Fig 6).
Lift up and remove “Face A” blade (Fig 7).
7.3 Attaching the blades
Identify “Face A” and “Face B” on your new set of DUALSAW blades (Fig 8).
Open lower guard and place “Face A” blade on saw and fit on the outer arbor shaft (Fig 9).
Place “Face B” blade on top of “Face A” blade and fit on inner arbor shaft (Fig 10).
Place lock nut onto shaft (Fig 11).
Tighten lock nut using blade wrench tool (Fig. 12).
8 OPERATION
8.1 Operating the saw
Push lock button and press the on/off trigger. Always let the blades reach full speed before
you begin to cut into the work piece.
Apply steady and even pressure when making a cut. Forcing the saw causes rough cuts
and could shorten the life of the saw or cause kickback.
Always feed material parallel to the blade. Feeding at an angle can burn the blade and
damage the blade teeth.
To stop the saw, release trigger.
8.2 Switching ON/OFF
To turn on the machine, push the ON/OFF switch in the ON position.
To turn the machine off, push the ON/OFF switch into the OFF position.
Inrush currents can cause short-time voltage drops; under unfavorable power supply
conditions, other equipment may be affected (if the system impedance of the power supply
is lower than 0,127 + j0,079 Ohm, disturbances are unlikely to occur); if you need further
clarification, you may contact your local power supplier.
8.3 Feed speed
Feed speed is how quickly you push the saw blades through the material being cut. The
correct feed speed is totally determined by the hardness and the thickness of the material
being cut.
If the feed speed is too slow the blades will only press down the material rather then cutting it.
The blade edges glide an wear down the material, what causes a poor cut and will cause
excessive wear on the blades.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0682 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0682 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0682

Powerplus POWX0682 User Manual - German - 12 pages

Powerplus POWX0682 User Manual - Dutch - 12 pages

Powerplus POWX0682 User Manual - French - 12 pages

Powerplus POWX0682 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info