582661
6
Zoom out
Zoom in
Previous page
1/10
Next page
POWX0520 EN
Copyright © 2015 VARO P a g e | 6 www.varo.com
Do not use bent, deformed or otherwise damaged saw blades.
Do not use saw blades which do not meet the specifications stated in this manual.
Before sawing, remove all nails and other metal objects from the workpiece.
Never start sawing before the saw reaches its full speed.
Securely clamp the workpiece. Never attempt to saw extremely small workpieces.
Only put the machine aside after switching off and when the saw blade has come to a
complete standstill.
Never try to slow the saw blade down by exerting pressure on the side.
Before performing maintenance to the machine, always unplug the machine.
7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Leaser beam warning
Laser beam characteristics
Warning! The laser beam potentially causes severe eye damage. Never look or stare
directly into the leaser beam.
During use, do not point the laser beam at people, directly or indirectly through reflecting
surfaces.
This laser complies with class 2 according to EN 60825-1:2007. The unit includes no
servicing components. Do not open the housing for any reason. If the unit is damaged,
have the damage repaired by an authorized repair agent.
8 ADJUSTMENTS
8.1 Replacing the saw blade (Fig. 1)
Only use sharp and undamaged saw blades. Cracked or bent saw blades must be replaced
immediately.
Place this circular saw on its side on a flat surface. Advice you bring the base plate (10)
down as if a minimum depth cut which is ease to operate.
Push the spindle lock button toward motor housing as the arrow shows in Fig. 1 and firmly
hold it.
Turn the blade clamp bolt anti-clockwise by using the spanner that supplied with the tool.
Remove the blade clamp bolt and outer flange.
Raise the lower guard (16) by using the lever for lower guard (17), and then remove the
saw blade.
Clean the saw blade flanges, then mount the new saw blade onto the output spindle and
against the inner flange.
Make sure the saw teeth and arrow on the blade is to be the same direction as the arrow
on the lower guard.
Reinstall the outer flange, and tighten the blade clamp bolt.
Make sure that the saw blade runs freely by turning the blade by hand.
Before replacing the saw blade always unplug the tool.
8.2 Adjusting the depth of cut (Fig. 2)
The depth of cut is infinitely adjustable. A clean cut is achieved with the saw blade protruding
from the material by approx. 3 mm.
Loosen the adjusting screw for depth adjustment (5).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0520 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0520

Powerplus POWX0520 User Manual - German - 11 pages

Powerplus POWX0520 User Manual - Dutch - 11 pages

Powerplus POWX0520 User Manual - French - 11 pages

Powerplus POWX0520 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info