645088
6
Zoom out
Zoom in
Previous page
1/11
Next page
POWX0477 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
Important: after completing sanding, switch off the switch and wait for the coasting sanding
head to stop completely before putting the tool down.
Never operate the tool in an area with flammable solids, liquids, or gases. Sparks from the
commutator / carbon brushes could cause a fire or explosion.
There are certain applications for which this tool was designed. The manufacturer strongly
recommends that this tool cannot be modified and / or used for any application other than
for which it was designed.
Use the machine with both hands at all times. Loss of control can cause personal injury.
Keep power supply cord clear from the working range of the machine. Always lead the
cable away behind you.
Immediately switch off the machine if unusual vibrations or if other malfunctions occur.
Check the machine in order to find out the cause.
The dust that arises when working with this tool can be harmful to health. Use a dust
absorption system and wear a suitable dust protection mask and remove deposited dust
with a vacuum cleaner.
6.1 Electrical connection
The network voltage must conform to the voltage indicated on the tool name plate. Under no
circumstances should the tool be used when the power supply cable is damaged. A damaged
cable must be replaced immediately by an authorized Customer Service Centre. Do not try to
repair the damaged cable yourself. The use of damaged power cables can lead to an electric
shock.
7 ASSEMBLY
Before setting up, repair or maintenance of the appliance you must always
turn off the operating switch and pull out the mains plug!
7.1 Before initial operation
Check if the rated frequency of the mains supply corresponds to the details of the type
place.
Before using the tool, read the instruction book carefully.
7.2 Shaft (21)
Fold the front and back part together (Fig. 1-1). Push the folding lock (9) to the right position
and keep the tip adjacent to the handle (Fig. 1-2), and then press the folding lock (9) towards
the handle until the end. (Fig. 1-3)
Unfold the handle by pushing the folding lock to the inside.
7.3 Remove / Assembly sanding head (1 / 2)
Pull the lock lever and slide to the left to remove the head (Fig. 2-1)
To assemble the head, firstly ensure the lock lever in release position, then connect the
motor housing (7) and big bearing cove to the head. Push the lock lever up to the right
lock position (Fig. 2-2)
7.4 Replace sanding pad (Fig. 3)
Insert the hex wrench (size 5) into the hexagonal screw bolt on the sanding block
Hold the sanding pad firmly, and then turn the wrench counter clockwise to dismount the
pad.
Install new sanding pad by tightening the bolt.
Attention: Only install the specified sanding pad on the machine.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0477 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0477 in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0477

Powerplus POWX0477 User Manual - German - 12 pages

Powerplus POWX0477 User Manual - Dutch - 12 pages

Powerplus POWX0477 User Manual - French - 13 pages

Powerplus POWX0477 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info