672428
7
Zoom out
Zoom in
Previous page
1/13
Next page
POWEG8010 EN
Copyright © 2018 VARO P a g e | 7 www.varo.com
9 OPERATION
9.1 Unit operation
Attention! Do not use the unit with out its protective cover. Always check
the unit's condition before you use it.
Before setting the unit into operation, check the unit's safety, especially for:
On/Off stop control
Gas lever and its holder
Operation of protective devices
Firmness, damage, and worn-out cutting components
Grips/handles - must be clean and dry
9.2 Use of the belt
Equip the attached harness.
Turn on the engine, return the throttle lever to the lowest speed position, and put the
harness hook to the hanging part of the machine.
Adjust the length of the harness so that the blade may be parallel to the ground in the
working position. In order to prevent slack during operation, turn up to ensure the extra
length of the band and not loose.
9.3 Engine starting (cold engine)
Attention! Never start the engine near the refueling site.
Important: Before starting the unit cut the cutting string to 13 cm in order to
avoid an engine overload during starting.
Place the unit on a firm and flat surface. Make sure the cutting components do not touch
any items or the floor.
Set the on/off stop control (7) to its "ON" position.
Press primer bulb 7 to 10 times, until the air bubbles are out.
Shift the choke lever (13) to its position marked “ ”.
Pull the starter rope grip a few times in order to provide the engine with enough fuel/air
mixture. Pull until the engine starts
Keep running until the motor is warm enough.
Move the choke lever around half open position.
Apply full gas and. •Let the engine run for 10 seconds in order to heat up. Push briefly the
gas lever (9), the engine will idle.
Move the choke lever (13) to its position marked “ ”.
If the engine does not start, repeat steps 2-10.
Attention! If the engine does not start after two attempts, try to start it
without choke. If even that does not work, then the engine is "flooded".
Follow the instructions specified in the chapter - "Engine does not start".
9.4 Engine starting (hot engine)
A hot engine is to be started without choke. Start it in the same way as a cold engine but make
the starting position around half way open.
9.5 Engine shutdown
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWEG8010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWEG8010 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWEG8010

Powerplus POWEG8010 User Manual - German - 15 pages

Powerplus POWEG8010 User Manual - Dutch - 15 pages

Powerplus POWEG8010 User Manual - French - 14 pages

Powerplus POWEG8010 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info