795558
9
Zoom out
Zoom in
Previous page
1/12
Next page
POWEB2510 EN
Copyright © 2018 VARO P a g e | 9 www.varo.com
11 GENERAL OPERATING INSTRUCTIONS
Slide a fully charged battery pack into the bottom of the handle, making sure that it clicks
into place. Be sure the battery pack is securely seated into the saw handle so it will not fall
off during use.
Firmly hold the reciprocating saw with both hands. Position the Blade near the work piece,
depress the lock-off button (3) and hold the ON/OFF switch trigger (4) down.
Release the lock-off button once the tool has power. Allow the saw to come up to full
speed before addressing it to the work piece.
IMPORTANT: Do not start the saw if the saw blade is in contact with
anything before operation. If necessary, lift the tool from the work piece
before squeezing the ON/OFF switch trigger.
In preparation for making a cut, place the pivot shoe assembly (1) on the surface to be cut.
Align the saw blade with the direction of the cut and slowly lower the saw blade onto the
cut line to begin the cut. Do not attempt to cut with the tip of the blade; kickback and
damage to the blade could result.
When finished cutting, release the ON/OFF switch trigger to stop the tool.
Remove the battery pack and the saw blade.
Clean, then store the saw indoors and out of children’s reach.
11.1 General cutting
Clamp your work piece if it is portable. Rest the front shoe of the saw on your work piece (be
sure the blade is not contacting the work piece) and start the saw, exerting enough pressure in
the direction of the cut to keep the shoe pressed firmly against the work piece at all times. Do
not force the cut or stall the saw. Don’t bend or twist the blade, let the tool and the blade do
the work.
In general, coarser blades are for wood, plastics, and composites, and finer blades are for
cutting metal. Chattering or vibration may indicate you need a finer blade or higher speed. If
the blade overheats or clogs, it may indicate you need a coarser blade. Replace blades when
they become dull. Dull blades will produce poor results and may overheat the saw.
11.2 Plunge cutting
Clearly mark the line of cut, from a convenient starting point within the cut out area. Place the
tip of the blade over that point with saw parallel to the line of cut, slowly lower the saw until the
bottom edge of the shoe rests on the work piece and the blade is not touching the work piece.
Start the saw and allow it to attain full speed. With the saw resting on the shoe, slowly tilt the
saw forward to lower the blade onto the cut line. Continue this motion until the saw blade is
perpendicular to the work piece.
11.3 Metal cutting
Blades specifically designated for cutting metals must be used for this purpose. You may use
light oil as a coolant when cutting metal, this will prevent overheating of the blade, help the
blade cut faster, and promote longer blade life.
12 CLEANING AND MAINTENANCE
12.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWEBRSS2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWEBRSS2 in the language / languages: English as an attachment in your email.

The manual is 0.46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWEBRSS2

Powerplus POWEBRSS2 User Manual - German - 13 pages

Powerplus POWEBRSS2 User Manual - Dutch - 13 pages

Powerplus POWEBRSS2 User Manual - French - 13 pages

Powerplus POWEBRSS2 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info