676332
5
Zoom out
Zoom in
Previous page
1/8
Next page
POWE40020 EN
Copyright © 2017 VARO P a g e | 5 www.varo.com
Take special care when sanding lead based paint:
All persons entering the work area must wear a mask specially designed for protection
against lead paint dust and fumes.
Children and pregnant women must not enter the work area.
Do not eat, drink or smoke in the work area.
Do not leave the tool running. Operate the tool only when hand-held.
Ventilate your work area adequately when you perform sanding operations.
Be sure that there are no cracks or breakage on the pad before use. Cracks or breakage
may cause a personal injury.
7 OPERATING INSTRUCTIONS
Before attempting to use your sander be sure to familiarize yourself with all its operating
features and safety requirements.
Warning! The sander should always be disconnected from the power
supply when assembling parts, marking adjustments, cleaning or when the
tool is not in use. Disconnecting the tool will prevent accidental starting
that could cause serious injury.
Do not sand plaster surfaces, (WARNING: In this case your guarantee
becomes void) this may clog the motor (brushes, ball bearings, ..).
7.1 Sanding
Hold the sander in front and away from you, keeping it clear of the work piece.
Start the sander
Let the motor build up to speed then gradually lower it on to the work with a slight forward
movement .
Move the sander slowly over the work piece using forward and back or side to side
strokes.
Upon completion of the sanding operation remove the sander from the work piece before
turning if off.
7.2 Switching On-off (Fig. 1)
Connect the plug to the power supply, the power-on indicator (4) is illumed until the tool
disconnect from the power mains.
The tool is switched On by the ON/OFF switch (2) located on the front of the tool housing.
Press On-off switch I/O
7.3 Attaching the sandpaper (Fig. 2)
Select sandpaper with the correct grain size. Make sure the perforations in the paper
coincide with those on the sanding base plate.
The sandpaper should rest flush on the base plate and must not come loose.
You can be sure to find the right sandpaper among our product range (see technical
specifications).
7.4 Dust Bag (Fig. 3)
The dust extraction system extracts sanding dust from the work piece through the holes in the
backing pad. The dust is then transferred through the dust extraction port on the rear of the
sander housing.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWE40020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWE40020 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWE40020

Powerplus POWE40020 User Manual - German - 9 pages

Powerplus POWE40020 User Manual - Dutch - 9 pages

Powerplus POWE40020 User Manual - French - 9 pages

Powerplus POWE40020 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info