675276
7
Zoom out
Zoom in
Previous page
1/10
Next page
POWE20010 EN
Copyright © 2017 VARO p a g e | 7 www.varo.com
Fit the desired disc (8) on the spindle and replace the outer flange and backing flange.
Release the spindle lock.
Important! Only ever press the spindle lock when the motor and grinding
spindle are at a standstill!
You must keep the spindle lock pressed while you change the wheel !
For grinding wheels up to approx. 3 mm thick, screw on the flange nut with the flat side facing
the grinding wheel.
7.4 Special attention when starting the machine
Clamp the workpiece and make sure that the workpiece cannot slide from under the
machine during the cutting activities.
When working with the machine, always hold it firmly with both hands and provide for a
secure stance.
Always direct the cable to the rear away from the machine.
Insert the mains plug only when the machine is switched off.
Apply the machine to the workpiece only when switched on
Never use the machine for grinding magnesium workpieces.
7.4.1 Switching On
Connect the plug to the power supply. The power-on indicator (9) is illumed until the tool
disconnect from the power mains.
Press the end of the ON/OFF switch down then slide it forwards until it locks.
The machine will start.
7.4.2 Switching Off
Unlock the ON/OFF switch, the machine will be switched OFF. The disc will gradually
slow down and eventually stop after a few seconds.
Do not put the machine down when the disc is still turning.
In case of interruption of the mains supply the on/off switch of the tool
needs to be released and reactuated.
8 OPERATON MODES
8.1 Grinding
Hold the handle (3) and auxiliary handle (6) firmly and
switch on. Avoid blocking the ventilation slots with your
hand, as this may cause the grinder to overheat. Let the
disc reach full speed. Apply the grinder to the item.
Maximum effect is achieved when the grinder is held at
an angle of 15-30°in relation to the item. Move the
grinder gently along the item. Give the grinder time to
work. It is rarely necessary to press the disc hard against the surface to be worked. Sparks
can occur in the motor compartment during use. This is normal and does not mean the grinder
is defective. Switch off the grinder after use.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWE20010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWE20010 in the language / languages: Dutch as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWE20010

Powerplus POWE20010 User Manual - German - 11 pages

Powerplus POWE20010 User Manual - Dutch - 12 pages

Powerplus POWE20010 User Manual - French - 11 pages

Powerplus POWE20010 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info