675072
5
Zoom out
Zoom in
Previous page
1/6
Next page
POWDP9010 EN
Copyright © 2018 VARO P a g e | 5 www.varo.com
In case of skin or eye contact, follow the instructions below:
Immediately rinse with water. Neutralize with a mild acid such as lemon juice or
vinegar.
In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not
incinerate the battery.
7 CHARGING AND INSERTION OR REMOVAL OF BATTERY
7.1 Charger indications
Connect the charger to the power oulet socket
Solid green: ready to charge
Flickering red: charging
Solid green: charged
Solid green and red: battery or charger damaged
Note: if the battery does not fit properly, disconnect it and confirm that the
battery pack is the correct model for this charger as shown on the
specification chart. Do not charge any other battery pack or any battery pack
that does not securely fit the charger.
1. Frequently monitor the charger and battery pack while connected
2. Unplug the charger and disconnect it from the battery pack when finished.
3. Allow the battery pack to cool completely before using it.
4. Store the charger and battery pack indoors, out of reach of children.
NOTE: If battery is hot after continuous use in the tool, allow it to cool down
to room temperature before charging. This will extend the life of your
batteries.
7.2 Removal / insertion of battery (Fig. 1)
WARNING: Before making any adjustments ensure the tool is switched off or
remove the battery pack.
To install: push and slide battery pack into battery port, make sure the release latch on the
rear side of the battery snaps into place and battery is secure before beginning operation.
To remove: Press the battery release latch and pull the battery pack out at the same time.
7.3 Battery capacity indicator
There are battery capacity indicators (2) on the battery pack, you can check the capacity status
of the battery if you squeeze the button (3). Before using the machine, please press switch
trigger to check if the battery is full enough for properly working.
Those 3 LED might show the status of the capacity level of the battery:
3 LED’s are litt: Battery fully charged
2 LED’s are litt: Battery 60% charged
1 LED is litt: Battery almost discharged
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWDP9010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWDP9010 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWDP9010

Powerplus POWDP9010 User Manual - German - 7 pages

Powerplus POWDP9010 User Manual - Dutch - 6 pages

Powerplus POWDP9010 User Manual - French - 6 pages

Powerplus POWDP9010 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info