795637
9
Zoom out
Zoom in
Previous page
1/12
Next page
POWDP4050 EN
Copyright © 2021 VARO P a g e | 9 www.varo.com
To install the belt proceed in reverse order.
10.3 Planing
Choose the desired cutting depth before operation.
Hold the planer with one hand on the switch and the other hand on the adjustment knob
(2).
Place planers shoe on the surface to be planed. Making certain that the cutting blades are
not touching the surface.
Push down firmly on the adjustment knob of the planer. So that the planers base is
completely flat on the work piece surface. Depress the lock-off button and push the trigger
switch. Allow the motor to reach full speed before starting to plane.
Move the tool slowly over the work piece and maintain downward pressure to keep the
planer flat. Be particularly careful to keep the tool flat at the beginning and the end of the
work piece surface.
ATTENTION: Never change the cutting depth while operating , to not create any
irregularities on the planed surface.
10.4 Rebating (Fig. 8a & 8b)
Insert the screw provided through the slot on the rebate. Turn the screw into the nut on
the housing.
The cut depth adjustment can be set from 0 to 8 mm
To adjust the depth of cut, place the planer on a flat board, then loosen the screw and
slide the cut depth adjustment guide up and down for required depth.
Tighten the thumb screw fully.
The depth of rebating cut is determines by moving the rebate and the number of passes made
along the workpiece. Make sure that the planer is guided with a lateral supporting pressure.
10.5 Edge chamfering (Fig. 9)
Always use both hands on the tool for any operation. It assures to maintain
control and avoid risk of serious personal injury. The workpiece must
always be properly supported and clamped so that both hands will be free
to control the planer.
Using the V-groove is the base plate you can make a chamfer on the work piece edge.
Guide the planer along the edge and maintain a constant angle and force to produce a
good finish.
You can control the angle of the chamfer with your hands.
Make a test chamfer on a scrap piece of wood.
Maintain downward pressure to keep your planer flat at the beginning and the end of the
work surface.
10.6 Dust extraction
When using the planer dust will be generated.
Always use the dust bag supplied with your product.
The dust extraction outlet can be connected to an external vacuum cleaner to extract while
operating.
11 CLEANING AND MAINTENANCE
Attention !Before performing any work on the equipment, pull the power
plug.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWDP4050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWDP4050 in the language / languages: English as an attachment in your email.

The manual is 0.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWDP4050

Powerplus POWDP4050 User Manual - German - 13 pages

Powerplus POWDP4050 User Manual - Dutch - 13 pages

Powerplus POWDP4050 User Manual - French - 13 pages

Powerplus POWDP4050 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info