676276
9
Zoom out
Zoom in
Previous page
1/10
Next page
POWAIR0805 EN
Copyright © 2014 VARO P a g e | 9 www.varo.com
Disconnect tool from air supply before attempting repair or adjustment.
When replacing O-rings or Cylinder, lubricate with air tool oil before
assembly.
PROBLEMS
POSSIBLE CAUSES
REMEDIES
Tool runs at
normal speed
but loses under
load
Motor parts worn.
Lubricating clutch housing.
Check for excess clutch oil. Clutch
cases need only be half full. Overfilling
can cause drag on high speed clutch
parts, i.e. a typical oiled/lubricated
wrench requires 1⁄2 ounce of oil.
GREASE
LUBRICATED:NOTE: Heat
usually indicates
insufficient grease in
chamber. Severe operating
conditions may require
more frequent lubrication.
Cam clutch worn or
sticking due to lack of
lubricant.
Tool runs
slowly. Air flows
slightly from
exhaust
Motor parts jammed with
dirt particles
Check air inlet filter for blockage.
Pour air tool lubricating oil into air inlet
as per instructions.
Operate tool in short bursts quickly
reversing rotation back and forth where
applicable.
Repeat above as needed.
Power regulator in
closed position
Air flow blocked by dirt.
Tools will not
run. Air flows
freely from
exhaust
One or more motor
vanes stuck due to
material build up.
Pour air tool lubricating tool into air inlet.
Operate tool in short bursts of forward
and/or reverse rotation where
applicable.
Tap motor housing gently with plastic
mallet.
Disconnect supply. Free motor by
rotating drive shank manually where
applicable
Tool will not
shut off
‘O’ rings throttle valve
dislodged from seat inlet
valve.
Replace ‘O’ ring.
Note: Repairs should be carried out by a qualified person.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWAIR0805 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWAIR0805 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWAIR0805

Powerplus POWAIR0805 User Manual - German - 12 pages

Powerplus POWAIR0805 User Manual - Dutch - 11 pages

Powerplus POWAIR0805 User Manual - French - 11 pages

Powerplus POWAIR0805 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info