582179
2
Zoom out
Zoom in
Previous page
1/4
Next page
POW910 EN
Copyright © 2012 VARO Page | 2 www.varo.com
PIVOTING ARM FOR HOIST
POW910
1 APPLICATION
The pivoting arm is designed to have one hoist attached to it. The pivoting arm must be
mounted on a well-attached steel rod for this purpose, which has a diameter of 48 mm.
2 DESCRIPTION
1. Bottom support
2. Clamping block
3. 2 bolts (M12 x 60 mm)
4. Upper support
5. Supporting arm
6. Cotter pin
7. Pivoting arm
8. Large cotter pin
9. Extension pipe
10. Bolt (M12 x 70 mm)
11. Bolt (M8 x 60 mm)
12. Rubber saddles
3 SYMBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal injury
or damage to the tool.
Read manual before use.
In accordance with essential applicable safety standards of European
directives.
4 SAFETY WARNINGS
Be sure to take the following points into account, so as to avoid accidents and injury:
§ Do not overburden the pivoting arm.
§ In case of damage, do not continue to use the pivoting arm.
§ For your own safety, make sure that all screws have been properly tightened and check
these regularly.
§ Always make sure that the cotter pins are properly fastened in the drill holes.
§ It is strictly forbidden to transport persons with the hoist.
§ In addition, persons may not stand under the hoist or pivoting arm.
§ A person that has not been informed about these safety regulations may not use this
product.
§ All components must be regularly checked for possible deformations or damages.
§ Always observe the maximum allowed load!
5 ASSEMBLY (FIG. A)
§ Position of the lower support (1) at the desired working height against a vertical steel tube,
which has a diameter of 48 mm and a wall thickness of at least 4 mm, and which surface
is not too smooth, to ensure a better grip.
§ Assemble with the clamping block (2) by means of 2 M12 x 60 mm bolts (3) and M12 nuts,
using Ø 12 mm spring washers and Ø 12 mm flat washers, and tighten properly (bolts
must be tightened to 70 Nm minimum).
§ Install of the upper support (4) and the clamping block (2) in the same manner. Make sure
that they are both installed in the same direction. The distance between both must be 420
mm, measured from the underside to the underside.
§ Hook one side of the support arm (5) into the hinge pin of the upper support (make sure it
is positioned in the correct direction), and secure it by inserting a cotter pin (6) in the hole
of the hinge pin.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW910 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW910

Powerplus POW910 User Manual - German - 5 pages

Powerplus POW910 User Manual - Dutch - 4 pages

Powerplus POW910 User Manual - French - 4 pages

Powerplus POW910 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info