481011

Powerplus POW8136 Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
POW8136 EN
Copyright © 2014 VARO P a g e | 7 www.varo.com
Before you connect the machine to the power supply, make sure the data on the rating
plate is the same as that for your mains.
9.2 Setting up the saw unit (Fig. 1/2)
To adjust the turntable (8), loosen the locking handle by approx. 2 turns, which frees the
turntable (8).
Turn the turntable (8) and scale pointer (11) to the desired angular setting on the dial (12).
Lightly press the machine head (4) down while at the same time pulling the retaining pin
(16) out from the motor mounting; this causes the saw to move down to the lower working
position.
Swing the machine head (4) up until the retaining hook latches into place.
The clamping device (19) and the workpiece support (20) can be fastened on both right
and left sides of the base plate (9).
By loosening the tightening screw (13), the machine head (4) can be angled to the left up
to 45°.
10 OPERATION
10.1 Making 90° crosscuts with turntable at 0° (Fig. 1/3)
For cutting widths up to 100 mm it is possible to fix the saw's drag function with the knurled
screw (14) in rear position. If the cutting width exceeds 100 mm you must ensure that the
knurled screw (14) is slackened and that the machine head (4) can be moved.
Bring the machine head (4) to its upper position.
Push the machine head (4) back by its handle (2) and affix in this position if necessary
(depending on the cutting width).
Place the piece of wood to be cut against the stop rail (7) and on the turntable (8).
Secure the workpiece in position with the clamping device (19) on the base plate (9) to
prevent the workpiece from moving during the cutting process.
Turn the release lever (1) to the left to release the machine head (4).
Push the ON/OFF switch (3) to start the motor. Using the handle (2), push downward all
the way through the work-piece with uniform and light pressure.
After the cutting process is finished, bring the machine head back to its upper (home)
position and release the ON/OFF button (3).
Caution! The resetting springs in the machine automatically raise the
machine head. Do not simply let go of the handle (2) after cutting, but allow
the machine head to slowly lift up by applying slight counterpressure.
10.2 Precision adjustment of the stop for crosscut 90° (Fig. 4/5)
Lower the machine head (4) and fasten in place with the safety pin (16).
Slacken the tightening screw (13).
Place the angular stop (a) between the blade (5) and the turntable (8).
Slacken the counternut and adjust the adjustment screw (21) until the angle between the
blade (5) and the turntable (8) equals 90°.
Retighten the counternut to secure this setting.
Finally, check the position of the angle indicator. If necessary, release the pointer with a
crosstip screwdriver, move to the 0° position of the angle scale (15) and retighten the
holding screw.
10.3 Making 90° crosscuts with turntable at 0° - 45° (Fig. 6)
With POW8136 you can make right and left angular cuts from 0° - 45° to the stop rail.
Use the handle (2) to set the turntable (8) to the desired angle i.e. the scale pointer (11) on
the turntable must coincide with the desired angular setting (12) on the stationary base
plate (9).
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW8136 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW8136 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW8136

Powerplus POW8136 User Manual - German - 12 pages

Powerplus POW8136 User Manual - Dutch - 12 pages

Powerplus POW8136 User Manual - French - 13 pages

Powerplus POW8136 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info