481005
8
Zoom out
Zoom in
Previous page
1/12
Next page
POW751 EN
Copyright © 2016 VARO P a g e | 8 www.varo.com
6.5 Spraying techniques (fig d.)
To obtain the best results, keep your spray gun level and parallel to the surface at all times.
Keep the nozzle 25 - 30 cm from the surface and spray evenly from side to side or up and
down. Do not spray at an angle as this will lead to paint runs on the surface. Use smooth and
even strokes. When spraying large areas, use a criss-cross pattern as shown.
Fig E.
Never start or stop the spray gun while it is aimed at the surface to be sprayed. Evenly control
the speed of movement of the spray gun. A fast speed of movement over the surface will give
a thin coat and a slow speed will give a heavy coat. Apply one coat at a time. If a further coat
is required, make sure you observe the manufacturers drying time recommendations before
applying a second coat. When spraying small areas, keep the output control on a low setting.
This will avoid using too much paint and prevent overspray. Where possible avoid stopping
and starting when spraying an object. This can lead to too much, or not enough paint being
applied. Do not tip the spray gun to more than 45 °C
6.6 Fitting and using the flexible nozzle (fig. F)
The flexible nozzle extension should be used to spray flat or horizontal surfaces. It should
also be used in areas with limited access. To fit the flexible nozzle, unscrew the basket nozzle
and attach the flexible nozzle in its place Replace the basket nozzle on the end of the flexible
nozzle and tighten.
7 CLEANING AND MAINTENANCE (FIG. G.)
Always remember to disconnect from the mains supply before cleaning the
spray gun or paint container.
It is essential that the spray gun is cleaned thoroughly after every use. Failure to clean it will
almost certainly result in blockages and it may not operate when you next come to use it! The
guarantee does not cover cleaning a sprayer that has not been properly cleaned by the user.
7.1 The following action must be taken after every use.
Empty any remaining material from the container.
Clean the container thoroughly with the thinner that was used.
Pour some thinner into the container and spray through the spray gun until only clean
thinner is coming out of the nozzle.
Thoroughly clean the paint pick up pipe and filter with thinner.
Clean the basket and nozzle and remove any other debris or paint that remains.
Turn the spray gun upside down and apply a few drops of light oil to the two apertures (F).
This will lubricate the piston and cylinder.
If your spray gun should require extra internal cleaning, it may be necessary to disassemble it.
If so the following actions should be taken.
Remove the plug from the mains socket.
Remove paint container, pick up pipe and filter.
Undo the 4 screws (G).
Take off the pump assembly.
Release the nozzle (H), valve (J), piston (K) and spring (L)
Clean the cylinder (M) and all parts thoroughly with solvent.
Apply a few drops of light lubricating oil to the piston, spring and cylinder.
Reassemble the spray gun.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW751 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW751 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW751

Powerplus POW751 User Manual - German - 12 pages

Powerplus POW751 User Manual - Dutch - 12 pages

Powerplus POW751 User Manual - French - 13 pages

Powerplus POW751 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info