481001
6
Zoom out
Zoom in
Previous page
1/10
Next page
POW7490 EN
Copyright © 2015 VARO P a g e | 6 www.varo.com
Check with a qualified electrician or service personnel if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly grounded.
6.2 Diamond blades
Only use 180mm diameter Continuous Rim Wet Diamond blades.
DO NOT use larger, segmented or 'turbo' blades, wood sawing blades, or any other
cutting device. Severe bodily injury, and damage to your saw can occur.
Inspect blades daily for cracks or uneven wear. Discard cracked, chipped or bent blades!
Ensure the blade is mounted with the rotation arrow in the proper direction and is securely
tightened with a wrench.
Always ensure a continuous flow of water on both sides of the blade before cutting any
material.
Do not operate the machine without all safety guards in position
Do not force the material into the blade. Let the blade cut at its own speed.
7 ASSEMBLY
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance.
7.1 Mounting the riving knife (fig. 1)
Unscrew the two (crosshead) screws and place the foot of the riving knife under the table.
Place the small plate (2 holes with thread) under the foot of the riving knife
Connect the riving knife with the two screws and the plate
7.2 Mounting the cutting disc (fig. 2 & 3)
Unscrew two screws out of lower blade guard and remove the guard. (fig. 2)
Dismount nut (counterclockwise) and outer flange
Place blade on the inner flange
Mount outer flange and nut (clockwise) again (fig. 3)
Place the lower blade guard back in position and connect the two screws
7.3 Mounting the upper blade guard (10) (fig. 4)
Slide the guard in horizontal position across the riving knife.
Connect the guard to the riving knife with the wing nut bolt and the locknut
Be aware that the guard is connected under the lockpin. The lock-pin prevents the guard
falling backwards.
7.4 Mounting the adjustable fence
Connect the knob (7) with the fence (3) by using the plate (1 hole with thread); do not
tighten the knob yet.
Slide the complete fence with (loosen) knobs onto the table; the plates on the inner side of
the table.
Set the required distance.
Tighten the knobs by rotating them (clockwise).
Place the water reservoir (4) under the table
8 OPERATION
The tile cutter may only be used as a fixed tool and should be screwed down to a level
and horizontal surface.
Use the screw holes in the base of the machine.
Keep water full in the tank when you operate the cutter.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW7490 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW7490 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW7490

Powerplus POW7490 User Manual - German - 11 pages

Powerplus POW7490 User Manual - Dutch - 10 pages

Powerplus POW7490 User Manual - French - 11 pages

Powerplus POW7490 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info