480905
9
Zoom out
Zoom in
Previous page
1/14
Next page
POW64256 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
9.9 Chain wheel
The chain wheel (16) is subjected to especially high wear and tear. If you notice deep wear
marks on the teeth, the chain wheel must be replaced. A worn chain wheel curtails the service
life of the saw chain. Have the chain wheel replaced by a specialist dealer or your Customer
Service.
9.10 Chain guard
The chain guard must be clipped onto the chain and sword as soon as the sawing work has
been completed and whenever the chainsaw has to be transported.
9.11 Chain brake
In the event of kick-back, the chain brake (3) will be actuated via the front finger guard. The
front finger guard is pushed forwards by the back of the hand and this causes the chain brake
to stop the chain saw, or rather the motor, within 0.15 s (Fig 5, H).
9.12 Releasing the chain brake (Fig 5)
To be able to use your chain saw again, you must release the saw chain again. First switch off
the chainsaw. Then push the front finger guard (3) back into the vertical position until it locks in
place (Fig 5, I). The chain brake is now fully functional again.
9.13 Sharpening the saw chain
You can have your saw chain sharpened fast and correctly by specialist dealers, from whom
you can also obtain chain sharpening equipment to enable you to sharpen the chain yourself.
Please follow the corresponding operating instructions.
Take care of your tools. Keep your tools sharp and clean to enable you to work well and safely.
Follow the maintenance regulations and the instructions for changing tools
10 STARTING UP
Always wear safety goggles, ear muffs, protective gloves and heavy-duty
work clothes!
Use the saw only with approved extension cables with the prescribed insulation and
connections designed for outdoor use (approved rubber-sheathed cables) which fit the
chainsaw plug.
The chain saw is equipped with two safety switches, requiring the use of both hand
The chainsaw works only when one hand holds the front grip (2) and the other hand actuates
the switch on the rear grip (1).
If the chainsaw does not run, the chain brake must be released at the front finger guard (3). Be
sure to read the sections Chain brake and Releasing the chain brake on this point.
After switching on, the chainsaw will run immediately at high speed .
10.1 To switch off
Release either the ON/OFF switch (13) on the rear grip or the other switch (2) on the front grip.
The release of ON/OFF switch results the stop of the chainsaw within 1sec., and heavy
sparkling. This is normal and safe for the proper operation of the chainsaw.
After working with the chainsaw, you should always: Clean the saw chain and guide bar and
replace the chain guard.
10.2 Chainsaw protection
Never use the chainsaw in the rain or in damp conditions.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW64256 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW64256 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW64256

Powerplus POW64256 User Manual - German - 15 pages

Powerplus POW64256 User Manual - Dutch - 15 pages

Powerplus POW64256 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info