582169
7
Zoom out
Zoom in
Previous page
1/11
Next page
POW2086 EN
Copyright © 2014 VARO p a g e | 7 www.varo.com
7.2 Replacing the grinding wheel
Before performing any work on the equipment, pull the power plug.
Simple wheel change by spindle lock: Press the spindle lock
and allow the grinding wheel to latch in place. Open the
flange nut with the face spanner.
Change the grinding or cutting wheel and tighten the flange
nut with the face spanner.
Important! Only ever press the spindle lock when the motor and grinding
spindle are at a standstill!
You must keep the spindle lock pressed while you change the wheel !
For grinding or cutting wheels up to approx. 3 mm thick, screw on the flange nut with the flat
side facing the grinding or cutting wheel.
7.3 Test run for new grinding wheels
Allow the right-angle grinder to run in idle for at least 1 minute with the grinding or cutting
wheel fitted in place. Vibrating wheels are to be replaced immediately.
Flange arrangement
1. Spindle catch
2. Guard
3. Clamping flange
4. Grinding wheel
5. Flange nut
7.4 Motor
It is vital for the motor to be well ventilated during operation. Be sure, therefore, to keep the
ventilation holes clean at all times.
7.5 Grinding wheels
Never use a grinding or cutting wheel bigger than specified diameter. Before using a grinding
or cutting wheel, check its rated speed. The wheels rated speed must be higher than the idle
speed of the right-angle grinder.
Use only grinding and cutting wheels that are approved for a maximum speed of 12000 min-1
and a peripheral speed of 80 m/sec.
8 OPERATING MODES
8.1 Rough grinding:
For the best rough grinding results, hold the grinding wheel at an angle of between 30° and
40° to the workpiece surface and guide back and forth over the workpiece in steady
movements.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW2086 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW2086 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW2086

Powerplus POW2086 User Manual - English - 8 pages

Powerplus POW2086 User Manual - German - 11 pages

Powerplus POW2086 User Manual - Dutch - 8 pages

Powerplus POW2086 User Manual - French - 11 pages

Powerplus POW2086 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info