391295
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWXQ5107 EN
Copyright © 2015 VARO NV P a g e | 7 www.varo.com
Turn the guard in the desired position and tighten it by locking the clamp. (if the clamp is
not tight enough, open it again, tighten the nut using a spanner, then lock the clamp again)
7.1.2 Repositioning (turn) / removing the guard
To reposition/turn the guard, release the quick clamp, turn the guard, and retighten the
clamp.
To remove the guard: if installed, first remove the mounted disc, then work in the opposite
as described above under mounting/installing the guard.
7.2 Installing / replacing the grinding wheel (fig 2)
Prior to mounting/dismounting an accessory always unplug the tool.
Only Use discs of the correct dimension and of good quality. (Use fiber-reinforced
cutting/grinding discs (for stone-metal) or diamond disc (for stone) only).
The grinding disc may not touch the edge of the guard.
Press the spindle lock (fig A, n° 5) and turn the spindle until it engages in the lock. Keep
the spindle lock pressed during this procedure.
Loosen and remove the flange nut from the spindle using the spanner.
Position the disc on the flange.
Place the flange nut on the spindle and tighten using the spanner.
Release the spindle lock and check that the spindle is unlocked by rotating it.
Make sure the disc is installed in the correct way (direction of rotation)
Important! Never press the spindle lock before the motor and disc have come
to a complete standstill!
Never use the spindle lock to stop the motor. It will break.
For grinding/cutting discs up to approx. 3 mm thick, screw on the flange nut with the flat side
facing the grinding or cutting wheel. (Fig 3)
Inspect discs regularly. Worn discs have a negative effect on efficiency of the machine
and may cause severe injury to user or damage to surrounding. Replace the grinding disc
on time.
7.2.1 Test run for new grinding wheels
When starting the tool, hold the tool in a well protected area and allow the angle grinder to
reach idle speed with the grinding/cutting disc fitted in place. Vibrating wheels are to be
replaced immediately.
7.3 Mounting the side handle (Fig 4)
The side handle can be used for both left-hand and right-hand control.
Fasten the side handle for left-hand operation on the right-hand side of the machine.
Fasten the side handle for right-hand operation on the left-hand side of the machine.
Fasten the side handle for upright working at the top of the machine.
Make sure that the side handle is fastened properly and cannot loosen
unexpectedly.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow xq5107 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow xq5107 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow xq5107

Powerplus pow xq5107 User Manual - German - 12 pages

Powerplus pow xq5107 User Manual - Dutch - 13 pages

Powerplus pow xq5107 User Manual - French - 12 pages

Powerplus pow xq5107 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info