389288
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWXQ5203 EN
Copyright © 2014 VARO P a g e | 7 www.varo.com
The switch should be in 'drill’ position when drilling holes in tiles.
*(1)selector switch (4) set for Hammer mode. / (2) selector switch (4) set for drilling mode.
8.5 Reversible action (left / right) (fig 6)
The direction of rotation on your drill can be reversed.
The direction of rotation is controlled by a lever (6) located above the on/off switch (9).
With your drill held in normal operation position the direction of rotation-lever (6) should be
positioned to the right of the trigger for forward drilling operation.
The direction of rotation is in reverse (left), when the lever is turned to the left of the on/off
switch.
Don’t change the direction of rotation while your drill is still turning.
8.6 Insert a drill / bit. (fig 7)
To open the keyless chuck, hold the rear ring, turn the front ring anti-clockwise. When
jaws are open sufficiently, insert the drill / bit and re-close the chuck turning the front ring
clockwise, tighten it securely.
To unlock, turn clockwise again)
9 USE
Use only correctly sharpened drill bits which are suitable for the material being drilled.
When drilling hard materials, firm pressure is required on the power tool. However,
excessive pressure does not improve performance and places unnecessary pressure on
the tool and its bit.
Always apply pressure in straight line with the drill whiling drilling. Use enough pressure to
keep the drill biting but do not push too hard to avoid stalling the motor or damaging the
drill.
Warning! If the drill stalls, release the trigger switch immediately and remove the drill from
the work to determine the cause of stalling.
Use the auxiliary handle where possible to gain extra control and to prevent fatigue.
Use auxiliary handle supplied with the tool. Loss of control can cause
personal injury!
To minimize the chance of sudden stalling and breaking through the material, reduce the
pressure on the drill and ease the drill .
Keep the motor running when pulling the drill back out of a drilled hole. This will help
prevent jamming.
9.1 Drilling in Metal
For maximum performance, use high speed steel bits for metal or steel drilling.
Turn drilling mode selector to drilling mode.
Use a center punch to mark the hole location on the workpiece.
Begin drilling at a very low speed to prevent the drill from slipping off the starting point.
Maintain a speed and pressure which allows cutting without overheating the bit. Applying
too much pressure will: overheat the drill, wear the bearing, bend or burn bits, produce off-
center or irregular shaped holes.
When drilling large holes in metal it is recommended to drill with a small drill at first, then
finish with a larger drill, also, lubricate the drill with oil to improve drilling action and
increase drill life.
9.2 Drilling in Wood
For maximum performance, use high speed steel bits for wood drilling.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow xq 5203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow xq 5203 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow xq 5203

Powerplus pow xq 5203 User Manual - German - 12 pages

Powerplus pow xq 5203 User Manual - Dutch - 12 pages

Powerplus pow xq 5203 User Manual - French - 12 pages

Powerplus pow xq 5203 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info