388925
13
Zoom out
Zoom in
Previous page
1/15
Next page
POW X117
EN
Copyright © 2007 VARO – Vic. Van Rompuy N.V. – www.varo.com
P a g e | 13
7 MAINTENANCE
Preventive maintenance performed by unauthorized personnel may result
in misplacing of internal wires and components which could cause serious hazard.
The machine should be repaired either by a factory authorized technician or our own service
department.
7.1 TOOL LUBRICATION
This tool requires no hourly or daily lubrication because it has been proper lubricated and is
ready to use. It is recommended that tools with gears be re-greased with a special gear
lubricant at every brush change. Or be re-lubricated after every 6 months of operation. Send
the complete tool to Service Center for this lubrication service. However, if circumstances
require that you should lubricate it by yourself, proceed as follows. Run the tool for several
minutes to warm it up. Switch off and unplug the tool. Remove the crank cap using a wrench
(standard accessory). Rest the tool on the table with the bit end pointing upwards. This will
allow the old grease to collect inside the crank housing. Wipe out the old grease inside and
replace with genuine hammer grease (standard accessory, 45 g; 1.6 oz). Fill only with 15 g
(0.5 oz) grease one time. Reinstall the crank cap and tighten with the lock nut wrench.
• Filling with more than the specified amount of grease can cause faulty
hammering action or tool failure.
• Do not tighten the crank cap excessively. It is made of resin and is
subject to breakage.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by the authorized service centers, always using genuine
replacement parts.
7.2 CARBON BRUSHES
The brushes and commutator in your tool have been engineered for many hours of
dependable service. To maintain peak efficiency of the motor, we recommend to have the
brushes examined every two to six months. Only genuine replacement brushes specially
designed for your tool should be used.
When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it
will automatically shut off the motor. When this occurs, both carbon brushes should be
replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes
should be replaced at the same time. Use only identical carbon brushes.
7.3 BEARINGS
After about 100-120 hours of operation, or at every second brush change, the bearings should
be replaced by our technical department. Bearings which become noisy (due to heavy load or
very abrasive material cutting) should be replaced at once to avoid overheating or motor
failure.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow x117 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow x117 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow x117

Powerplus pow x117 User Manual - German - 15 pages

Powerplus pow x117 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info