613966

Powerpeak FET8319P Energy Line Manual

39
Zoom out
Zoom in
Previous page
1/69
Next page
39
H.R.C. (Heart Rate Control)
You can choose from five training options: THR (Target Heart Rate), 55%, 65%, 75% and 85%.
55% : Target Heart Rate (target number of heartbeats) = 55% of (220-AGE)
65% : Target Heart Rate (target number of heartbeats) = 65% of (220-AGE)
75%: Target Heart Rate (target number of heartbeats) = 75% of (220-AGE)
85%: Target Heart Rate (target number of heartbeats) = 85% of (220-AGE)
55%, 65%, 75% and 85%
These programs allow you to train at 55% (P18), 65% (P19), 75% (P20) or 85% (P21) of your maximum heart
rate for a certain period of time. Press the START key to begin training and keep the palms of your hands on the
hand pulse sensors during the training. The computer will adapt the resistance automatically during the
training in order to reach the set value. If the value of your heart rate is lower than the set value, the computer
will automatically increase the resistance. If the value of your heart rate is higher than the set value, the
computer will automatically reduce the resistance.
Note: it is not possible to manually adjust the resistance during this program.
T.H.R. (Target Heart Rate)
This program allows you to train at a set maximum heart rate. Press the START key to begin training and keep
the palms of your hands on the hand pulse sensors during the training. The computer will adapt the resistance
automatically during the training in order to reach the set value. If the value of your heart rate is lower than the
set value, the computer will automatically increase the resistance. If the value of your heart rate is higher than
the set value, the computer will automatically reduce the resistance.
Note: it is not possible to manually adjust the resistance during this program.
User program
With the user programs P14 - P17 you can create your own program. The settings and values will be stored in
the computer memory.
Watt-program
This program allows you to train at a certain level Watt. Press START and place your palms on the hand pulse
sensors during training. The computer will automatically adjust resistance during training to reach the set
value.
Note: it is not possible to manually adjust the resistance during this program.
Set values
You are able to set the different values, once a program has been selected. Press ENTER to select a value. Once
you have selected a value, it will start blinking. You can now adjust the value by pressing the UP and DOWN
buttons. Confirm by pressing the ENTER button.
Note: the values TIME and DISTANCE cannot both be set. You need to choose one of these two values.
Start
Once you have selected a program and all values are set, press START to begin training. Once the pre-set value
is reached, a tone sounds and the program stops automatically.
Heart Rate Measurement
Press START and then press ENTER until the PULSE function appears in the display. Keep your palms on the
hand pulse sensors. Your heart rate is measured in beats / minute.
Note: if no signal is transmitted to the sensors within 16 seconds, the message "P" appears in the display. This
is an energy saving mode. Repeat the above steps to measure your heart rate again.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerpeak FET8319P Energy Line at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerpeak FET8319P Energy Line in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info