659075

Powerfix Z32118 - IAN 107580 Manual

9
Zoom out
Zoom in
Previous page
1/55
Next page
GB/IE 9
Q
Before start of operation
Q
Insert / replace battery
Tip: Low voltage symbol showing in the LCD display
3
indicate a discharged / flat battery.
Tip: When changing the battery, the LCD display
3
may
experience faults. Remove the battery and insert it again.
j
Push the battery compartment button
4
, and then pull out
the battery receptacle
7
(see fig B).
j
Remove the old battery.
j
Insert battery receptacle containing the new battery into the
battery compartment and ensure correct polarity (+ and –).
Make sure that the plus terminal points outwards.
j
Push the battery receptacle
7
fully in (see Fig. B).
Q
Starting up the device
Q
Using the angle ruler
j
Press the ON/OFF button to switch the LCD display
3
on.
j
Loosen the locking knob
2
by turning it anti-clockwise.
j
Put on a flat surface. Make sure both rulers
1
are aligned with
the surface (see fig. C), and then press ZERO button
6
to set
data to zero.
j
Rotate the ruler to measure the angle. Note: The locking
knob
2
can be tightened by turning it clockwise, so as to
hold a desired measured angle.
j
You may also open the 2 rulers 180° straight aligned with
the surface (see fig. D), and then press ZERO button
6
to
set zero. Rotate the ruler to measure the angle.
Tip: The display will show “Err”, if the ruler has been turned
over 360° (see fig. E). Turn back the ruler to the original
starting point and measure again.
Tip: The LCD display
3
automatically switches itself off after
approx. 4 minutes.
Q
Troubleshooting
The device contains sensitive electronic components. That is why
it experiences interference when in close proximity to radio
transmission devices. If any indication errors appear in the
display, remove such devices out of the proximity of the angle
ruler.
Electrostatic discharge could result in malfunctions.
j
When such malfunctions occur, remove the battery for a
short while and re-insert.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerfix Z32118 - IAN 107580 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerfix Z32118 - IAN 107580 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info