624610
243
Zoom out
Zoom in
Previous page
1/379
Next page
Parking 243
Programming a button on the keypad
Caution!
Risk of damage. When programming a gara-
ge door or gate, the door or gate may open
and close several times in quick succession,
causing the motor to overheat.
f Unplug the garage door or gate during the pro-
gramming procedure to prevent the motor
from overheating.
1. Press and hold the desired button on the
keypad until light-emitting diode B starts to
flash slowly (may take up to 20 seconds).
Do not release the button before step 3 has
been completed.
2. Hold the original remote control approx.
5–30 cm in front of the marked position C.
Make sure that the battery in the original
remote control is new.
3. Press and hold the button on the original remo-
te control until light-emitting diode B flashes ra-
pidly.
The rapidly flashing LED B confirms that the re-
mote control function has been programmed
successfully.
Only release both buttons when LED B flashes.
4. Press the programmed button on keypad A.
If the light-emitting diode B lights up conti-
nuously after programming, this means that
the system is a fixed-code system. Program-
ming is now completed.
If light-emitting diode B again flashes rapidly
for a short time after programming and then
lights up continuously for approx. 2 seconds,
this means that the system is a changeable-
code system. HomeLink must then be synchro-
nized with the receiver of the garage door ope-
ner after programming.
5. Repeat steps 1 to 4 to program the other
buttons.
Synchronization for changeable-code
systems
1. To synchronize the system:
Press the programming button on the receiver
of the garage door opener.
Afterwards, you usually have approx.
30 seconds to initiate step 2.
2. Press the previously programmed button on
the keypad three times (for approx. 1 second).
Changeable-code synchronization is now com-
pleted.
3. Repeat steps 1 to 2 to synchronize other
signals to the other buttons.
Note
f Please consult an authorized Porsche dealer if
you have not been able to successfully assign
signals to the buttons even though you have
carefully followed the instructions in this
section and the operating instructions for the
original remote control. Your authorized
Porsche dealer also has a list of all compatible
garage door opener systems.
Operating the garage door opener
f Press the corresponding button on keypad A.
Light-emitting diode B lights up continuously
during signal transmission with fixed-code
systems.
In the case of signal transmission for change-
able-code systems, light-emitting diode B
repeatedly lights up rapidly for a short time
and then lights up continuously for approx.
2seconds.
10_Cayenne_21_KW17.book Seite 243 Donnerstag, 9. April 2009 3:33 15
243


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Porsche Cayenne at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Porsche Cayenne in the language / languages: English as an attachment in your email.

The manual is 14,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info