628495
86
Zoom out
Zoom in
Previous page
1/105
Next page
however its value will not be used for filter computations. This valid/invalid parameter information above is
provided mainly as guidelines for programmers writing control software for the Vortex. If a parameter is not valid
for a specific filter type, then the control for editing that parameter should be disabled or removed when that
filter type is selected.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01PEQIA3,2,1,1250,40,-20,1,1
Set the parametric
EQ on input 3 , band
2 to the following
parameters: type =
parametric filter,
frequency = 1250
Hz, bandwidth = 40
1/100th octaves,
gain = -20 dB,
enabled = yes, slope
= 1 dB per octave.
The value of the
slope parameter is
irrelevant for this
type of filter, we
could have set it to
anything.
F01PEQIA3,2,1,1250,40,-20,1,1
F01PEQIAB,1,?
Query the current
parameter settings
for the parametric
eq filter on input B ,
band 1.
F01PEQIAB,1,t,f,b,g,s,e , where the
parameters t, f, b, g, s, and e correspond to
the current settings of the type, frequency,
bandwidth, gain, slope, and enabled parameters,
respectively. If this filter was set to the same
parameters as given in the above example, the
status message would be
F01PEQIAB,1,1,1250,40,-20,1,1 .
8.104. PEQIB -- Set Bandwidth Parameter for Specified
Parametric EQ Input Stage
This command sets or queries the bandwidth parameter (in 1/100th octaves) for the parametric equalizer (EQ)
filters on input channels 1-8 and A-D . Each channel has five bands of parametric EQ that can be independently
controlled.
The minimum and maximum values for the bandwidth parameter are 5 and 200, respectively.
This command has the same format and restrictions as the
PEQIA command except that only one parameter, the
bandwidth, is specified instead of all the parameters. See the
PEQIA command for more information. To set the
bandwidth parameter for an output parametric EQ filter, use the
PEQOB command. To set all the parameters for
an output parametric EQ filter, use the
PEQOA command.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info