648863
6
Zoom out
Zoom in
Previous page
1/8
Next page
VAPORELLA POWER SYSTEM
29
pliance to an appropriate collection facility at
the end of its useful lifespan.
Appropriate separate collection to permit recy-
cling, treatment and environmentally compati-
ble disposal helps prevent negative impact on
the environment and human health and promo-
tes recycling of the materials making up the
product. For more information on available col-
lection facilities, contact your local waste col-
lection service or the shop where you bought
this appliance.
II
II
MM
MM
PP
PP
OO
OO
RR
RR
TT
TT
AA
AA
NN
NN
TT
TT
Before leaving our factory all our products are
rigorously tested. This is the reason why your
VAPORELLA may contain some residual water
in the boiler.
PP
PP
RR
RR
EE
EE
PP
PP
AA
AA
RR
RR
AA
AA
TT
TT
II
II
OO
OO
NN
NN
FF
FF
OO
OO
RR
RR
UU
UU
SS
SS
EE
EE
1a. Rest the board on the floor.
2a. To open the ironing board, just pull the iron-
ing surface upwards keeping a foot on Va-
porella side leg of the board until locking
takes place (fig. A).
To adjust height, unfasten the lever (O) and
move the board upwards or downwards.
NOTE: Because of the weight of the ironing
surface, during closing and height adjust-
ment hold the board with both hands.
3a. Insert the cable holder (M) in its location
(fig. 1).
4a. Place the monoflex (iron power supply -
steam tube) (E) in its support (fig. 2).
5a. Unscrew the safety cap (A) and fill the
boiler with about 1 litre of water using the
filler bottle (I)
(fig.3) making sure that it
does not overflow.
Normal tapwater can be used. However, as
hard water by its nature contains limestone,
which may cause a build-up of limescale in
the boiler, in hard water areas we recom-
mend the use of our natural-base decalci-
fier KALSTOP, available from your Polti
dealer or by mail order from your Polti serv-
ice Centre.
WARNING: Do NOT under any circumstan-
ces put or leave the filler bottle in the water
filling aperture of the appliance when the
appliance is connected to the mains electri-
city supply. Danger of burns!
6a. Connect the power supply cable (D) into an
earthed power supply of the correct volt-
age.
7a. Press the main switch (B); the steam pres-
sure indicator (K) and the “iron heating” in-
dicator light (J1) light up (fig. 4).
8a. To operate the board, turn the board main
switch (C) on. In this way the board heater
starts working.
Wait a few minutes to allow the heater to
reach working temperature.
It is now possible to activate blowing and
suction features:
9a. BLOWING: By pushing the function switch
(P) on position (I), the board allows you to
swell the clothes with a “hot blow”, so that
you can gently skim with the iron the most
delicate clothes, ironing them with steam
only.
10a. SUCTION: By pushing the function switch
(P) on position (II), the board holds the
clothes to the surface and eliminate the
residual humidity.
Note: to avoid condensation inside the
ironing board we recommend to use the
suction function while steam ironing.
II
II
NN
NN
SS
SS
TT
TT
RR
RR
UU
UU
CC
CC
TT
TT
II
II
OO
OO
NN
NN
SS
SS
FF
FF
OO
OO
RR
RR
UU
UU
SS
SS
EE
EE
Before ironing a garment, it is always advisable
to check the symbols and instructions on the la-
bel provided by the garment manufacturer.
Check which kind of ironing is recommended,
referring to the table below:
Steam ironing allowed
For dry ironing, set the iron tempera-
ture on •••
Steam ironing allowed
For dry ironing, set the iron tempera-
ture on ••
Check the fabric's resistance to
steam ironing, dry iron allowed with
temperature set on •
- do not iron
- steam ironing or treatment not al-
lowed
EE
EE
NN
NN
GG
GG
LL
LL
II
II
SS
SS
HH
HH
vl power system m0s06959 1l12.qxp 18/01/2006 15.37 Pagina 29
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polti Vaporella Power System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polti Vaporella Power System in the language / languages: English as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polti Vaporella Power System

Polti Vaporella Power System User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info