Manual Polti Sani System Polti Check (page 11 of 13) (English)

648795

Zoom out

Zoom in

1/13

To change the paper roll, proceed as follows:

• Open the lid of the printer by pressing the

OPEN key (D3) (Fig.8).

• Position a paper roll inside the compart-

ment, observing the direction of rotation as

indicated (Fig.9).

• Pull the end of the paper so that it leads out

of the compartment, then close the lid

(Fig.10).

• Tear off the excess paper against the serra-

ted edge (Fig.11).

• It is possible to move the paper forward by

pressing the FEED key (D4).

Use thermal paper for slips, easily found on

the market. Store the paper in a dry place and

away from direct sunlight in order to ensure a

longer life both of the paper and of the data

printed on it.

If you purchase any new cards over and

above those supplied with the machine, they

will have to be initialized.

With the machine switched off, press keys 1

and 2 on the numerical keypad, both at the

same time. Use the switch (A) to turn on the

machine, then release keys 1 and 2. The indi-

cation “INITIALIZE CARD XX” will appear on

the display (XX corresponds to the number of

the card to be initialised. It is a progressive

number that cannot be repeated). Insert the

new CARD in the slot. Do not remove the

CARD until the information “CARD XX INI-

TIALIZED” appears on the display. Remove

the CARD from the slot. Once the card has

been removed, the system will prompt you to

initialize another card. To do this, follow the

instructions as above. To exit, turn of the ma-

chine using the switch (A). A CARD that has

already been initialised cannot be overwritten.

Before carrying out any maintenance on

the device, always unplug it from the

power mains and allow it to cool down

before proceeding.

If the monotube is torn, it must be replaced by

an authorised service centre.

Cleaning of the delivery nozzle

Clean the delivery nozzle every 10-15 hours

of use. Clean the delivery nozzle using the

brush (T) included in the supply, sliding it in-

side the tube so as to remove any residues of

scaling in it (Fig.12).

Lubrication of the coupling

Whenever it is difficult to fit the connector (Q)

and in any case when the device has not

been used for some time, lubricate the cou-

pling on the bottom of the delivery device

(fig.13) with a synthetic lubricant. It you find it

difficult to insert the connector even after lu-

bricating, contact an authorized service cen-

ter.

Tips

In the event of external factors such as, for

example, a sudden change in voltage due to

an upset in the network (failure, lightning,

etc.), the device may be affected by electrical

interference and be subject to temporary mal-

functioning.

To reset the device, switch it off and discon-

nect it from the mains for a few minutes. After

this procedure, start it again normally. If it still

does not work correctly, ask for a check up at

an authorised service centre.

Having the device checked after a problem of

this kind is recommended.

External cleaning

For cleaning the outside of the device we re-

commend using a damp cloth. Do not use sol-

vents or detergents as these could damage

the surfaces. Pay special attention to the

cleanliness of the outside of the device when

moving from one room to another, cleaning

the wheels too.

SANI SYSTEM CHECK

SANI SYSTEM CHECK M0S08111 2O08:A5 31/07/2008 11.27 Pagina 49

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polti Sani System Polti Check in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polti Sani System Polti Check Manual

Product: