Manual Polisport Joy (page 7 of 71) (All languages)

772285

Zoom out

Zoom in

1/71

| 4 | www.polisport.com

For child safety and for your peace of mind, Polisport has developed the

perfect child carrying solution that’s suitable for a wide range of adult

bicycles.

Our ergonomic child seats are all built with safety and comfort as the

primary goals.

In this manual, you will ﬁnd information on attaching the child bicycle seat

to the frame of your bicycle.

Carefully read the manual for a safe and correct installation of the child

bicycle seat.

REAR CHILD-SEAT FOR BICYCLE

FRAME MOUNTING SYSTEM

• This child bicycle seat must not be mounted to bicycles ﬁtted with rear

shock absorbers.

• This child bicycle seat must not be mounted to a racing bicycle with

drop handlebar.

• This child bicycle seat must not be mounted to Motorized Vehicles such

as Mopeds and Scooters.

• This child bicycle seat must not be mounted in bicycles with triangular,

square or carbon ﬁber frames.

• This child bicycle seat must be assembled on bicycles with round and

oval frames with diameters ranging from Ø28 to Ø40 mm.

• The child bicycle seat must be assembled on bicycles with wheels with

diameters of 26” and 28”.

• The child bicycle seat can also be assembled on bicycles with wheels

with diameters of 29” if you acquired that speciﬁc child seat model.

• This child bicycle seat is only suitable for carrying children with a

maximum weight of 22 Kg (and children with recommended ages ranging

from 9 months to 5 years of age - with the weight as the decisive variable).

• The total weight of the cyclist and the child transported must not exceed

the maximum permitted load permitted for the bicycle. Information on

the maximum load can be found in the operating instructions of the

bicycle. You can also contact the manufacturer for this question.

• The seat may only be mounted on a bicycle suitable for the attachment

of such additional loads.

• The position of the child bicycle seat must be adjusted so that the bicycle

rider does not touch the child bicycle seat with the feet when in motion.

• It’s very important to adjust correctly the seat and its component parts

for optimum comfort and safety of the child. It’s also important that the

seat does not slope forward, so that the child does not tend to slide out of

it. It’s also important that the backrest slope backward slightly.

• Check if all parts of the bicycle function correctly with the child bicycle

seat mounted.

• Check the instructions of the bicycle, and If you have any doubts

on ﬁtting the child bicycle seat to your bicycle, please contact your

bicycle supplier for further information.

TECHNICAL FEATURES

1. Turn the child seat upside down as shown in the image. Cut the plastic

straps that hold the mounting block (I).

2. Use the Allen key No. 5 (I5) to loosen and remove the metal mounting

plate (J1).

3. Remove the attachment part of the metal bracket (J5) and set aside

for later use.

4. Disengage and remove the metal bracket (H) from the child seat,

pulling it upwards.

5. Hold the metallic bracket (H) the same as in the picture and pass it

through the opening in the child bicycle seat.

6. In order to adjust the child bicycle seat according to the bicycle size, set

the metallic bracket (H) into one of the three allowed positions to move

the seat backward or forward. At the beginning we suggest to place it on

the position No. 3.

7. Place the attachment part for the metal bracket (J5).

8. Insert the metallic mounting plate (J1) on the grooves of the child

bicycle seat, and close it as indicated in the picture.

9. While ﬁrmly securing the mounting set, lift the cushion (G) and ﬁrmly

grasp the M8 screw (J2), pushing it down.

10. Place the washer (J3) on the screw (J2). Then tighten securely with the

key (I5). Tighten tightly so that the metal bracket (H) is securely fastened.

This step is extremely important for the safety of the child.

11. Remove the screws (I1) on the mounting block (I), with the Allen key

no. 5 (I5).

12. Before placing the block onto the frame, make sure that the protective

rubber (I7) is correctly positioned on front of the block.

13. Place the main body of the mounting block (I2) on the front of the

bicycle frame, and then place the metallic mounting plate (I4).

Note: If they are cables in this area make sure that they are correctly

positioned in the central groove of the metallic plate, (between the

protective rubber (I7) and the groove of the mounting plate (I4) and are

able to move freely).

14. Place the washer (I6) in the M6 screws (I1), and then screw them on

to the mounting block (I). Tighten the screws, with the Key (I5), so that the

mounting block (I) is secured but not fully tightened so that, if necessary,

you can adjust the height later. However, note that it should be tight to

make it easier to complete the next step. You need to tighten the 4 screws

diagonally and in stages. Check the safety of the fasteners regularly.

15. Place the edges of the metallic bracket (H) at the holes of the metallic

bracket (I) until you hear a click indicating the lock, and until the center

button (I3) shall be level with the exterior of the hose metallic bracket.

16. Centre and adjust the metallic bracket (H) at a height above the

rear wheel, so that later, when you add the weight of the child, the

child bicycle seat does not touch the wheel. Note that the metallic

bracket (H) should be positioned at a maximum of 10 cm away from

the wheel. The child seat has a center of gravity (F) (engraved on the

child seat) that must be positioned in front of the rear wheel axle. If it

is positioned behind the axle, the distance must not exceed 10 cm.

If the center of gravity is at a upper distance from the axle, adjust the

metal bracket to one of the available positions. Special care must also be

taken when positioning the child seat to ensure that the cyclist does not

touch the child seat with his feet when cycling.

Note: In Germany, according to the German Traﬃc Law StVZO, bicycle

seats may only be ﬁxed so that 2/3 of the seat depth or the Gravity Center

of the seat is located between the front and rear axle of the bicycle.

17. After adjusting the height and positioning of the seat, hand tighten

the mounting block (I) to ensure that it cannot move. This tightening must

be manual and is extremely important for the safety of the child. Make

sure that the mounting block (I) is ﬁrmly attached. You need to hand tight

the 4 screws diagonally, with the same force and in stages (I5).

18. Pass the safety belt (C) around the bicycle frame. Adjust it as shown

in the picture, under tension. Make sure that remain loosen belt is not in

contact with the wheel. This step is extremely important for the child’s

safety.

ASSEMBLY INSTRUCTIONS

A. Main seat

B. Safety belt

B1. Safety lock

B2. Belt adjuster

B3. Central belt adjuster

B4. Hole for belt adjustment

C. Safety belt for bicycle frame

D. Footrest strap

E. Footrest

F. Centre of Gravity

G. Cushion

H. Metallic bracket

I. Mounting block

I1. Screws M6x45

I2. Plastic mounting block

I3. Release button

I4. Metallic mounting plate

I5. Allen key no. 5

I6. Lock washer M6

I7. Protective rubber

J. Metallic mounting Kit

J1. Metallic mounting plate

J2. M8x25 screw

J3. M8 washer

J4. M8 nut

J5. Metal bracket attachment part

K. Batch serial number

TABLE OF CONTENTS OF PRODUCT

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polisport Joy in the language / languages: All languages as an attachment in your email.

The manual is 3.48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polisport Joy Manual

Product: