Manual Polisport Guppy junior plus (page 6 of 70) (All languages)

773024

Zoom out

Zoom in

1/70

| 4 | www.polisport.com

1. Turn over the seat as shown in the picture.

2. Unscrew the hand knob (G1) and simultaneously lift the red security

ring (G2). Open the jaw (G3) to an aperture wider than the luggage carrier.

3. Place the seat on the luggage carrier and then fasten the hand knob

(G1) so that the seat remains slightly attached to the luggage carrier.

Check if the jaw (G3) is properly fastened to the luggage carrier.

4. The child seat has a centre of gravity (F) (inscribed on the child seat) that

must be positioned in front of the rear wheel axle. If it is positioned behind

the axle, the distance must not exceed 10 cm. If the centre of gravity is

more than this distance from the axle, adjust the seat to the correct

position. Special care must also be taken when positioning the child seat

to ensure that the cyclist does not touch the child seat with his feet when

cycling. Make sure that the mounting plate (G) is ﬁrmly attached to the

carrier before proceeding. This step is extremely important for child and

cyclist safety. Check the safety of the fasteners regularly.

Note: In Germany, according to the German Traﬃc Law StVZO, bicycle

seats may only be ﬁxed so that 2/3 of the seat depth or the Gravity Center

of the seat is located between the front and rear axle of the bicycle.

5. Fasten the hand knob (G1) so that the seat is well attached to the

luggage carrier. As soon as the hand knob is well tightened, make sure the

security lever is properly held as shown in the picture.

6. Pass the safety belt (C) around the bicycle frame. Adjust it as shown

in the picture, under tension. Make sure that remain loosen belt is not in

contact with the wheel. This step is extremely important for the child’s

safety.

7. The Guppy Junior seat must always be used with wheel protectors (D3).

They are strictly mandatory as it stops your child’s foot from coming into

contact with the wheel and prevent accidents. Place the protective ﬁlm

for the fork (E5) to cover the location where the metal plate will be applied

(E1). Polisport provides this ﬁlm for the protection of the fork and is not

responsible for any damage to the forks.

8. Fit metal attachment plate Ø[17-21]mm (E1) on the rear wheel’s right

hand fork. Repeat the same process for the left hand side.

9. Place the zip ties (D4) in the wheel protector (D3) as shown in the

picture. Is mandatory to install the 6 zip ties on each wheel protector.

10. Start to attach the zip ties (D4) to the bicycle fork. The zip tie located

on the bottom should be attached after the metal attachment plate (E1).

11. Attach the other 3 zip ties to the wheel bar by choosing the holes

that better ﬁt to your bicycle wheel size. Follow the picture instructions

for the guidance.

12. Cut the remaining tape and leave at least 4mm as shown in the

picture. Make sure you have followed all the previous steps before you

go to the next instruction. Test your bicycle wheel to make sure your

wheel turn around with no issue. Repeat this process on both sides of the

bicycle. Make sure you have both wheel protectors installed as described

in the instruction. You’re now ready to go to the next step to install the

retractable footrest.

13. Please do not proceed with this step before you follow the previous

steps to install the wheel protector. This is important for you and your child

security. Fit the fastening block (E2) to the metal attachment plate (E1)

After putting this component in place, ensure that its attachment pins

ﬁt properly into the metal attachment plate (E1), as shown on the above

image. Repeat the same process for the left hand side. Polisport does not

accept liability for any damage caused to the fork if this part is tightened

incorrectly.

14. Fit the retractable footrest (D2) onto the plate and block assembly

(E2+E1) installed previously to the rear wheel’s right hand fork. Repeat the

same process for the left hand side.

15. After ﬁtting the retractable footrest (D2), insert the M6 bolt into the

top slot and tighten the footrest (D2) onto the block installed on the rear

wheel’s right hand fork in the previous steps. After inserting the 2 bolts,

use the no. 4 Allen key (E4), to tighten them (6N.m) to ensure that they

do not come loose with daily use. Repeat the same process for the left

hand side.

• This junior bicycle seat must not be mounted to bicycles ﬁtted with rear

shock absorbers.

• This junior bicycle seat must not be mounted to Motorized Vehicles such

as Mopeds and Scooters.

• This junior bicycle seat must be assembled on a carrier with at least 38kg

/ 83.78 Lbs of capacity.

• For safety reasons this seat shall only be ﬁtted to luggage carriers in

accordance with ISO 11243 - 120 to 175 mm. Also ﬁtting wider carriers

- 185mm.

• This junior bicycle seat must be assembled on bicycles with wheels with

diameters of 26”, 27.5”, 28” and 29”.

• This junior bicycle seat is only suitable for carrying children with a

maximum weight of 35 Kg, minimum height of 1,10mts and above 6 years

of age, that are able to secure and keep their balance autonomously on

the seat during the ride.

• The total weight of the cyclist and the child transported must not exceed

the maximum permitted load permitted for the bicycle. Information on

the maximum load can be found in the operating instructions of the

bicycle. You can also contact the manufacturer for this question.

• The seat may only be mounted on a bicycle suitable for the attachment

of such additional loads.

• The position of the junior bicycle seat must be adjusted so that the

bicycle rider does not touch the child bicycle seat with the feet when in

motion.

• It’s very important to adjust correctly the seat and its component parts

for optimum comfort and safety of the child. It’s also important that the

seat does not slope forward, so that the child does not tend to slide out of

it. It’s also important that the backrest slope backward slightly.

• Check if all parts of the bicycle function correctly with the junior bicycle

seat mounted.

• Check the instructions of the bicycle, and If you have any doubts

on ﬁtting the junior bicycle seat to your bicycle, please contact your

bicycle supplier for further information.

ASSEMBLY INSTRUCTIONS

TECHNICAL FEATURES

A. Main seat

B. Safety belt

B1. Safety lock

B2. Belt adjuster

C. Safety belt for bicycle frame

D. Foot protector and footrest

assembly

D1. Foot protector

D2. Retractable footrest

D3. Wheel protector

D4. Zip ties (12)

E. Assembly kit for foot

protector and footrest (D2)

E1.

Metal attachment plate Ø[17-21]mm

E2. Fastening block

E3. Bolts M6

E4. No. 4 Allen key

E5. Protective ﬁlm for the fork

F. Centre of Gravity

G. Mounting plate to luggage

carrier

G1. Hand knob

G2. Safety red ring

G3. Jaw

H. Cushion

I. Batch serial number

TABLE OF CONTENTS OF PRODUCT

For child safety and for your peace of mind, Polisport has developed the

perfect child carrying solution that’s suitable for a wide range of adult

bicycles.

Our ergonomic junior seats are all built with safety and comfort as the

primary goals.

In this manual, you will ﬁnd the information to attach the junior seat to

the carrier.

Carefully read the manual for a safe and correct installation of the

junior bicycle seat.

REAR JUNIOR SEAT FOR BICYCLE

CARRIER MOUNTING SYSTEM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polisport Guppy junior plus in the language / languages: All languages as an attachment in your email.

The manual is 3.59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polisport Guppy junior plus Manual

Product: