Manual Polisport Bubbly Mini (page 7 of 68) (All languages)

772288

Zoom out

Zoom in

1/68

| 4 | www.polisport.com

1. Turn the child seat upside down as shown in the image. Cut the plastic

straps that hold the mounting block (I).

2. Remove the metallic bracket (H) from the seat by cutting the straps.

Disengage and remove the metallic bracket (H) from the child seat, pulling

it upwards.

3. Use the Allen key No. 5 (I5) to loosen and remove the metal mounting

plate (J1).

4. Hold the metallic bracket (H) the same as in the picture and pass it

through the opening in the child bicycle seat.

5. Insert the metallic mounting plate (J1) on the grooves of the child

bicycle seat, and close it as indicated in the picture.

6. Place the washer (J3) on the screw (J2). Then tighten securely with the

key (I5). Tighten tightly so that the metal bracket (H) is securely fastened.

This step is extremely important for the safety of the child.

7. Remove the screws (I1) on the mounting block (I), with the Allen key

no. 5 (I5).

8. Before placing the block onto the frame, make sure that the protective

rubber (I8) is correctly positioned on front of the block.

9. Place the main body of the mounting block (I2) on the front of the

bicycle frame, and then place the metallic mounting plate (I4).

Note: If they are cables in this area make sure that they are correctly

positioned in the central groove of the metallic plate, (between the

protective rubber (I8) and the groove of the mounting plate (I4) and are

able to move freely).

10. Place the washer (I6) in the M8 screws (I1), and then screw them

on to the mounting block (I). Tighten the screws, with the Key (I5), so

that the mounting block (I) is secured but not fully tightened so that, if

necessary, you can adjust the height later. However, note that it should

be tight to make it easier to complete the next step. You need to tighten

the 4 screws diagonally and in stages. Check the safety of the fasteners

regularly.

11. Place the edges of the metallic bracket (H) at the holes of the

mounting block (I) until you hear a click indicating the lock, and until the 2

green safety device indicators pop up on the front of the mounting block.

The child bicycle seat will only be properly installed when the 2 green

safety device indicators are visible. This step is extremely important for the

child’s safety.

12. After adjusting the height and positioning of the seat, hand tighten

the mounting block (I) to ensure that it cannot move. This tightening must

be manual and is extremely important for the safety of the child. Make

sure that the mounting block (I) is ﬁrmly attached. You need to hand tight

the 4 screws diagonally, with the same force and in stages (I5).

13. (B) To place the child in the seat, ﬁrst open the belt. Start by pressing

the releases on the sides of the safety buckle (B4) and pull the buckle (B1)

upwards, so that it slides out of the socket (B5). Place the child in the seat.

Insert the safety buckle (B1) in its socket again (B5). Make sure that the

buckle socket (B5) is correctly positioned and does not hurt the child.

Next, adjust the belt to the size of the child to ensure that the child is

ﬁrmly secured. First adjust the height of the belt. To do this, pull the straps

according to the size of the child. Before starting the journey, always check

that the child is secured and that the belt is snug but not so tight that it

hurts the child. We recommend that the child’s helmet be put on after the

belt is adjusted. Note: Always use the restraint system.

(B.A) To place the child in the seat, ﬁrst fully extend the belt straps (B),

sliding the adjusters (B2). This makes it easier to put the helmet when the

child is in the seat. Do the same for the other side. To put the child in the

seat, open the lock (B1) of the safety belt (B) pressing the three buttons of

the lock (B1) as indicated. Before starting your ride, make sure the seat belt

is properly adjusted and that it does not hurt the child. This adjustment

is made by sliding the belt adjustors (B2). Note: Always use the restraint

system.

14. To adjust the height of the footrest (E) to ﬁt your child, release the

footrest (E) from the seat (A) by pressing the two fasteners together and lift

• This front baby seat must not be mounted to bicycles ﬁtted with rear

shock absorbers.

• This front baby seat must not be mounted to a racing bicycle with drop

handlebar.

• This front baby seat must not be mounted to Motorized Vehicles such as

Mopeds and Scooters.

• This front baby seat must not be mounted in bicycles with triangular,

square or carbon ﬁber frames.

• This front baby seat must be mounted on non-moving parts of the

bicycle.

• This front baby seat must be assembled on bicycles with round and oval

frames with diameters ranging from Ø28 to Ø40 mm.

• The front baby seat must be assembled on bicycles with wheels with

diameters of 26” to 29”.

• This front baby seat is only suitable for carrying children with a maximum

weight of 15 Kg (and children with recommended ages ranging from 9

months to 3 years of age - with the weight as the decisive variable).

• The total weight of the cyclist and the child transported must not exceed

the maximum permitted load permitted for the bicycle. Information on

the maximum load can be found in the operating instructions of the

bicycle. You can also contact the manufacturer for this question.

• The front baby seat may only be mounted on a bicycle suitable for the

attachment of such additional loads.

• The position of the front baby seat must be adjusted so that the bicycle

rider does not touch the child bicycle seat with the feet when in motion.

• It’s very important to adjust correctly the seat and its component parts

for optimum comfort and safety of the child. It’s also important that the

seat does not slope forward, so that the child does not tend to slide out of

it. It’s also important that the backrest slope backward slightly.

• Check if all parts of the bicycle function correctly with the front baby

seat mounted.

• Check the instructions of the bicycle, and If you have any doubts on

ﬁtting the front baby seat to your bicycle, please contact your bicycle

supplier for further information.

ASSEMBLY INSTRUCTIONS

TECHNICAL FEATURES

A. Main seat

B/B.A. Safety belt

B1/B.A1. Safety lock

B2. Belt adjuster

B3. Central belt adjuster

B4. Safety buckle releases

B5. Safety buckle socket

C. Back cushion

D. Footrest strap

E. Footrest

F. Seat cushion

G. Batch serial number

H. Metallic bracket

I. Mounting block

I1. Screws M8x45

I2. Plastic mounting block

I3. Release button

I4. Metallic mounting plate

I5. Allen key no. 5

I6. Lock washer M8x16

I7. Safety device indicator

I8. Protective rubber

J. Metallic mounting Kit

J1. Metallic mounting plate

J2. M8x16 screw

J3. M8 washer

TABLE OF CONTENTS OF PRODUCT

For child safety and for your peace of mind, Polisport has developed the

perfect child carrying solution that’s suitable for a wide range of adult

bicycles.

Our ergonomic child seats are all built with safety and comfort as the

primary goals.

In this manual, you will ﬁnd information on attaching the front baby seat

to the frame of your bicycle.

Carefully read the manual for a safe and correct installation of the front

baby seat.

FRONT BABY SEAT FOR BICYCLE

FRAME MOUNTING SYSTEM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polisport Bubbly Mini in the language / languages: All languages as an attachment in your email.

The manual is 2.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polisport Bubbly Mini Manual

Product: