HOW TO ASSEMBLE YOUR CHILD SEAT ON A LUGAGGE CARRIER
1. First clip the front part of the MIK Carrier Plate (G) and then the rear part,
by fitting the Locking Button (G1) into the grooves of the MIK CARRIER HD.
To proof that the operation is well succeed you must hear a “click” and a
green sticker will appear on the rear top part of the Unlocking Button (G2).
2. The child seat has a centre of gravity (F) (inscribed on the child seat) that
must be positioned in front of the rear wheel axle. If it is positioned behind
the axle, the distance must not exceed 10 cm. If the centre of gravity is
more than this distance from the axle, adjust the seat to the correct
position. Special care must also be taken when positioning the child seat
to ensure that the cyclist does not touch the child seat with his feet when
cycling.
Note: In Germany, according to the German Traffic Law StVZO, bicycle
seats may only be fixed so that 2/3 of the seat depth or the Gravity Centre
of the seat is located between the front and rear axle of the bicycle.
If the original positioning of the MIK LUGGAGE PLATE (G) of your seat does
not allow installation according to the above centre of gravity, or if you
intend to move the seat back and forward for your comfort, follow the
steps below to re-align the MIK LUGGAGE PLATE (G).
3. Remove the Metallic Mounting Plate (H1) with the Allen Key Nr.5. Install
again the MIK carrier plate (G) on the child seat (A). Pass the extremities of
the plate through the opening in the child seat (A).
4. To adjust the child bicycle seat according to the bicycle size, set the
MIK carrier plate (G) into one of the two allowed positions to move the
seat backward or forward. At the beginning we suggest placing it on the
position No. 2.
5. Place the washer (H3) on the screw (H2). Then tighten securely with the
Allen key (H4). Tighten tightly so that the Metallic Mounting Plate (H1) is
securely fastened. This step is extremely important for the safety of the
child and the cyclist. We recommend using a Torque of 6 N.m.
6. Pass the safety belt (C) around the bicycle frame. Adjust it as shown in the
picture, under tension. Make sure that remain loosen belt is not in contact
with the wheel. This step is extremely important for the child’s safety.
7. Make sure you have followed and fulfilled all the instructions given.
When done so, the child bicycle seat is ready for use. IT IS MANDATORY
TO READ the following chapter on safety instructions about using
your child bicycle seat.
ASSEMBLY INSTRUCTIONS
BUBBLY MAXI PLUS MIK HD
HOW TO ADJUST THE CHILD SEAT TO YOUR CHILD
1. To place the child in the seat, first fully extend the belt straps (B), sliding
the adjusters (B2). This makes it easier to put the child in the seat. To put
the child in the seat, open the lock (B1) of the safety belt (B) and press the
three buttons of the lock (B1) as indicated.
According to the child growth you can adjust the height of the belt on the
hole for belt adjustment (B4).
Note: Before starting the journey, always check that the child is secured
and that the belt is snug but not so tight that it hurts the child. We
recommend that the child’s helmet be put on after the belt is adjusted.
Note: Always use the restraint system.
2. To adjust the height of the footrest (E) to fit your child, release the
footrest (E) from the seat (A) by pressing the two fasteners together and
lift the footrest as indicated in the picture (it may be necessary to apply
some pressure to the fasteners
3. To reattach the footrests, first engage the top pin, and push the footrest
(E) down to lock the clips into the slots holes.
4. To guarantee your child’s safety, adjust the strap (D) of the footrest.
Unlock the strap (D) and adjust it to the child’s foot. Lock it again making
sure the strap does not hurt the child.
1. Detach the safety-belt (C) in order to remove the child bicycle seat. To remove the child seat (A) from the MIK HD CARRIER, push the Locking Button (G1)
and press the handle (G2), simultaneously lifting the seat.
ASSEMBLY INSTRUCTIONS
BUBBLY MAXI PLUS MIK HD
HOW TO REMOVE YOUR CHILD SEAT FROM A LUGAGGE CARRIER
• The rider must be at least 16 years of age; Check legislation and national
regulations pertaining to this.
• Make sure that the weight and height of the child do not exceed
the maximum capacity of the seat, and check this at regular
intervals. Check the weight of the child before using the child
seat. Under no circumstances should you use the child bicycle
seat to transport a child whose weight is above the permissible
limit.
• Do not carry a child less than 9 months of age in this child bicycle seat. To
be a passenger, the child must be able to sit up straight with the head held
upright while wearing a bicycle helmet. A doctor should be consulted if
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Polisport Bubbly Maxi Plus at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Polisport Bubbly Maxi Plus in the language / languages: All languages as an attachment in your email.
The manual is 3.41 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
