294948

Polaroid 600 autofocus Manual

10
Zoom out
Zoom in
Previous page
1/19
Next page
600/600 SE Camera User Guide
10
Coat black and white prints: Prints from all
black and white films except Type 667 must
be coated as soon as possible to protect
them from scratches, fingerprints and fading,
and to prevent changes in tone. For details,
see the film instructions. Do not coat color
prints.
Type 665 negatives: These must be
immersed in a sodium sulfite solution
immediately after separation from the
positive print. See the instructions on the
inside of the fim box for full details.
Protect film from heat: Keep film away
from heat. Extreme heat and humidity can
damage it, especially after the pack is
removed from its sealed foil wrapping.
Troubleshooting
If no white tab appears: Open the door
and, without moving the film pack, push the
white tab out (49). Then close and latch the
door.
If no yellow tab appears when you pull
the white tab: Do not pull another white tab.
Instead, carefully open the holder far enough
to get a finger on top of the film pack to hold it
down (50). Grasp the topmost yellow tab,
and gently pull it all the way out and discard it
(51). Inspect the rollers and clean them if
necessary. Close and latch the holder, with
the next white tab sticking out.
Picture faults and probable
causes
Repeated, evenly-spaced spots: Due to
dirt on the steel rollers in the film holder.
Missing corners or orange-red marks
along edges: Caused by pulling the yellow
tab out of the camera at an angle. Also
caused by dried developer chemicals at the
ends of the steel rollers in the film holder.
Oblong in print: The white tab was not
pulled all the way out. When the yellow tab
was pulled, the white tab was pulled back into
the camera.
Many small white specks: Caused by
pulling the yellow tab out too fast. This can
also cause pink lines, streaks or blotches on
color prints.
Picture with dull, weak colors: The print
was not developed long enough.
Underdeveloped color prints may be
brownish pink.
Picture with reddish tint and muddy
colors: The picture was developed at
temperatures below 65
o
F (18
o
C).
Color prints much too red: May occur with
some electronic flash units when set at
“Auto”.
Very light image or none at all: The film
was fogged or extremely overexposed. Do
not remove the safety cover from the film
pack before inserting it into the camera, and
do not remove a loaded film holder from the
camera without inserting the dark slide. Be
sure your exposure is based on the correct
film speed.
Nearly black image or solid black:
Caused by insufficient or no exposure. Be
sure you have cocked the shutter and
removed the dark slide. Be sure your
exposure is based on the correct film speed.
Broad streak or curtain-shaped mark:
Due to hesitation or stopping while pulling the
yellow tab out.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polaroid 600 autofocus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polaroid 600 autofocus in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info