Manual Polar PFL 1010 (page 2 of 2) (English)

632188

Zoom out

Zoom in

1/2

5019 801 01001

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 49* 1.90 2:00

Cotton 60 5.0 44 0.95 2:10

Cotton with “Eco”** 60 6.0 49 1.02 2:20

Cotton 40 5.0 44 0.60 2:00

Synthetics 60 2.5 50* 0.70 1:30

Synthetics 40 2.5 45 0.55 1:15

Delicates 30 1.5 50 0.50 0:45

Daily load 40 3.0 45 0.45 1:00

Quick wash 30 3.0 40 0.40 0:30

Wool

40 1.0 55 0.60 0:45

Handwash 40 1.0 45 0.60 0:40

Add detergents as indicated on the front page

and as described in the chapter “Detergent and

Additives” in your Instructions for Use.

Close the door and turn the programme

selector to the desired programme and

temperature. The indication lamp next to the

“Start/Pause” button flashes and the indication

lamp of the predefined spin speed lights up.

CONSUMPTION DATA

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the

home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type

of wash.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the

lamp lights to show the the door can be opened.

As long as a wash programme is running, the door

remains locked and must on no account be forced

open. In case you have an urgent need to open

it during a running programme, refer to “Cancel

(Reset) a running programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be

caused by a fault in an electrical component.

Refer to the “Troubleshooting Guide” in your

“Instructions for Use”; if the fault persists, contact

our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply.

Open the water tap: if the indications still lights

up, refer to the “Troubleshooting Guide” in the

Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether

the drain hose is kinked or the filter must be

cleaned: in the latter case refer to the Instructions

for Use (“Removing the Filter”).

“Prewash”

button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time

by approximately 15 min.

• Do not use liquid detergent for the main wash

when activating the Prewash option.

“Intensive rinse” button

• More water is added and rinse cycle is

prologned.

• This option is particularly suitable for areas

with very soft water, washing baby linen and

helps people with allergies.

“Easy ironing” button

• Can be used together with “Cotton”,

“Synthetics” and “Daily load” programmes to

make ironing easier.

• Increases the water quantity and the clothes

are spun very gently.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain

during the rinse. The water is drained out only.

PROGRAMME START

Open the tap and press the “Start/Pause”

button. The indication lamp next to the “Start/

Pause” button lights up. The programme

sequence indicator shows the current programme

phase, running from left to right through Wash,

Rinse, Spin/Drain.

When the programme phrase is finised, the

corresponding indication goes out.

PROGRAMME END

• All the lights of the programme sequence

indicator are off, and the “Door open”

indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the “Start/Pause” button again. The

new programme continues at the same

position where the previous programme was

interrupted.

Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before

the end.

•

Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the

door can be opened.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the

respective indication lamp lights up.

When the combination of programme and

additional option(s) is not possible, the indication

lights switch off automatically.

Unsuitable combinations of options are deselected

automatically.

“Eco” button

• With a modified temperature profile and a

slightly prologned washing duration, the

optimum combination of excellent washing

result and even lower energy consumption is

achieved.

START DELAY

The “Start delay” allows to run the machine at

the consumer's convenience, for example at night

when electricity is cheaper.

Do not use liquid

detergent when activating “Start delay” option.

• Select programme, temperature and options.

• Press the “Start delay” button to select the

delay time by 1, 3, 6, 9 or 12

hours.

• Press the “Start/Pause” button.

The indication next to the “Start delay” button

lights up and goes off when the programme

starts.

• Once having pressed the “Start/Pause”

button, the countdown of the time delay

begins. When the programme starts, the start

delay indicator light goes off and is replaced by

the programme sequence indication.

• After the “Start/Pause” button has been

pressed, the number of hours preselected can

be reduced by pressing again the “Start delay”

button.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another

position or press the “Reset”

button.

.after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 second

- the start delay indicator light goes out.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polar PFL 1010 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polar PFL 1010

Polar PFL 1010 User Manual - English - 14 pages

Polar PFL 1010 User Manual - German - 13 pages

Polar PFL 1010 User Manual - Dutch - 13 pages

Polar PFL 1010 User Manual - French - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polar PFL 1010 Manual

Product: