464058
26
Zoom out
Zoom in
Previous page
1/37
Next page
7. USING A NEW ACCESSORY
A new sensor purchased as a separate accessory has to be introduced to the cycling computer. This is
called teaching and takes only a few seconds. Teaching ensures that your cycling computer receives
signals from your sensor only, enabling disturbance-free exercise in a group. If you have purchased the
sensor and the cycling computer as a set, the sensor has already been “taught” to work together with the
cycling computer. You just need to activate the sensor in your cycling computer.
You can teach one speed, cadence and power sensor for each bike setting.
Teaching a New Speed Sensor
Select Settings > Bike SET > Bike1/ 2 / 3 > Speed SET > ON. Speed TEACH? is displayed
To teach a new sensor, make sure you are not near (40 m/131 ft) other speed sensors. To confirm
teaching, press OK. Test drive is displayed. To activate the sensor, press OK and rotate the wheel a few
times. A flashing red light indicates that the sensor is activated. Completed! is displayed once the teaching
process is over. The cycling computer is now ready to receive speed and distance data.
If Teaching FAILED is displayed, the cycling computer may be detecting the signal of more than one sensor
or the sensor is not activated. Make sure you are not near (40 m/131 ft) other speed sensors and press
OK. Try again? is displayed. Press OK and rotate the wheel a few times to activate the sensor.
If you want to cancel teaching, press STOP. The already taught speed sensor is taken into use.
For a video tutorial, go to http://www.polar.com/en/polar_community/videos.
Teaching a New Cadence Sensor*
Select Settings > Bike SET > Bike 1/ 2 / 3 > Cadence SET > ON. Cadence TEACH? is displayed
To teach a new sensor, make sure you are not near (40 m/131 ft) other cadence sensors. To confirm
teaching, press OK. Test drive is displayed. To activate the sensor, press OK and rotate the crank a few
times. A flashing red light indicates that the sensor is activated. Completed! is displayed once the teaching
process is over. The cycling computer is now ready to receive cadence data.
If Teaching FAILED is displayed, the cycling computer may be detecting the signal of more than one sensor
or the sensor is not activated. Make sure you are not near (40 m/131 ft) other cadence sensors and press
OK. Try again? is displayed. Press OK and rotate the crank a few times to activate the sensor.
If you want to cancel teaching, press STOP. The already taught cadence sensor is taken into use.
For a video tutorial, go to http://www.polar.com/en/polar_community/videos.
Teaching a New Power Output Sensor*
Select Settings > Bike SET > Bike 1/ 2 / 3 > Power SET > ON.
If you use the Polar LOOK Kéo Power system, follow the instructions below:
For the Polar LOOK Kéo Power system to work properly, the cycling computer must use the default power
settings. Even if you know the correct settings for your bike, do not use them.
C. length: Set chain length as 1473 mm. Accept the set value with OK.
C. weight: Set chain weight as 304 g. Accept the set value with OK.
S. length: Set span length as 420 mm. Accept the set value with OK.
If you use the Polar Power Output Sensor™ W.I.N.D., follow the instructions below:
C. length: Set chain length in millimeters. Accept the set value with OK.
C. weight: Set chain weight in grams. Accept the set value with OK.
S. length: Set span length in millimeters. Measure the distance from the centre of the rear hub to the
centre of the bottom bracket as shown in the picture. Accept the set value with OK.
ENGLISH
26 Using a New Accessory
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polar CS 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polar CS 500 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polar CS 500

Polar CS 500 User Manual - German - 43 pages

Polar CS 500 User Manual - Dutch - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info