Manual Plastimo Echofish 400 (page 5 of 34) (English, German, Dutch, French, Italian, Swedish, Spanish)

634484

Zoom out

Zoom in

1/34

NOTE: *** Incorrect use: Do not allow the cable

to sink to the bottom as it may become entangled

in debris.

*** The float can be removed if not

needed as follows:

1) Cutting off the rubber stopper from the cable .

2) Sliding the safety strap and float towards the

plug and gently remove.

NOTE:

*** *** To remove the sonar sensor from the frozen

ice, gently tap sonar sensor at the base with your

hand. If it will not come loose, spray a small amount

of water on the ice surface around the base and

repeat above step until the sonar sensor is easily

removed.

Never use a blunt to strike the sonar sensor as this

may cause damage to the sensitive internal

electronics.

*** Cold weather is extremely hard on the electrical

components within the display housing. It is

suggested that you keep the unit in temperatures

above 0 degrees Fahrenheit (-17 degrees Celsius)

during operation.

*** Remove the batteries from the fish finder to

prevent battery leakage and corrosion when not in

use.Clean the sonar sensor and cable with fresh

water and dry-off before storing .Do not submerge

and/or spray the fish finder screen/housing with

water or use chemicals to clean.

To achieve the best performance for ice fishing, it is

highly recommended that you cut a hole through the

ice and place the sonar sensor directly in the water.

If you would like to check the area for depth or

NOTE:

If depth readings appear as" ---" while using one of

these methods, place the sonar sensor directly in the

water to verity that the fish finder is operating

properly.

If it operates properly while directly in the water,

reposition the sensor in a new location in the hull, as

in above 8.1.3. If it still does not work, you may have

to place the sensor directly in the water for proper

operation as it will not work on all hull structure

designs.

Depth Range Min : 2feet (0.6M)

Measure Units: Feet and meters

Main unit is not submersible: IPX4

Operational Temperature: -4 to 158°F (-20—70°C)

1)Round Transducer with 25ft Cable

3)Stainless Bolt /Wing nut

2)Transducer Adapter

4)Neck Strap

10 Attachments:

9 Product Specification:

Display :

16 level grayscale

160V x 160H

Sensor Beam Angle: 45 degrees

4-AAA alkaline Batteries

Depth Range Max : 240feet (73.2M)

8.2 FISHING ON ICE

8 FISHING AT THE BOAT OR ICE

8.1 FISHING AT THE BOAT

8.1.1 Lower the sensor and float into the water as

per the previous instructions or-

8.1.2

Attach the adapter to the boat hull using the

mounting tabs or-

8.1.3

“shoot –Thru” the hull of a boat.

Place the sonar sensor in 1 inches of water against

the hull bottom. Or coat the face of the sonar sensor

with petroleum jelly and press it against the hull

bottom with a twisting motion.

Backlighting : White LED

Power Requirement:

fish before cutting the hole, clear away snow to

expose the ice surface, making sure the surface is

smooth.

Place a small amount of liquid water on the ice and

set the sonar sensor on the water allowing the unit to

freeze to the ice.

If there are any air pockets between the sonar senor

and ice, or air on the water below the ice, the unit will

not work properly and will require you to try another

spot, or cut a hole in the ice to use.

CORRECT INCORRECT

7.4

Use a pole to guide the sonar sensor to a

desirable position or add floats on the cable to float

on top of the water.

-4-

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Plastimo Echofish 400 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Plastimo Echofish 400 Manual

Product: