455198
43
Zoom out
Zoom in
Previous page
1/56
Next page
Additional information
43
En
08
08
Chapter 8:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Take a look at the
other components and electrical appliances being used,
because sometimes the problem may lie there. If the trouble
isn’t sorted out even after going through the checks below,
ask your nearest Pioneer authorized independent service
company to carry out repair work.
• If the unit does not operate normally due to external
effects such as static electricity disconnect the power
plug from the outlet and insert again to return to normal
operating conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power
will automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 40).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
The power suddenly turns on or off, or the input suddenly
changes (When the Control with HDMI is ON).
This happens because of the synchronized operation due to
the Control with HDMI function. If synchronized operations
are not needed, set the Control with HDMI to OFF (see HDMI
Setup on page 41).
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (see page 2).
Lower the volume level.
OVER TEMP
shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (see page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use VOL +/– to turn up the volume.
Press MUTE to turn muting off.
Make sure the component is connected correctly (refer to
Connecting your equipment on page 9).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (refer to
Connecting your equipment on page 9).
Check The Input Assign menu on page 39 to make sure you’re
assigned the correct input.
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
For HDMI, or when Video Converter is set to OFF and a TV and
another component are connected with different cords (in
Video Converter on page 39), you must connect your TV to this
receiver using the same type of video cable as you used to
connect your video component.
Some components (such as video game units) have
resolutions that may not be converted. If adjusting this
receiver’s Resolution setting (in Resolution on page 40) and/or
the resolution settings on your component or display doesn’t
work, try switching Video Converter (in Video Converter on
page 39) OFF.
No sound from subwoofer.
When using a powered subwoofer, make sure the subwoofer
is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 37 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 34 to 0dB or -5dB.
No sound from surround or center speakers.
Connect the speakers properly (refer to page 10).
Refer to Speaker Setting on page 37 to check the speaker
settings.
Refer to Channel Level on page 38 to check the speaker levels.
The Phase Control feature doesn’t seem to have an audible
effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 38).
Considerable noise in radio broadcasts.
Connect the antenna (page 17) and adjust the position for
best reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page 17).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (refer to page 17).
A vibrating sound emanates from the speakers while the
AM radio is automatically tuning.
The noise is to increase reception capabilities and is not a
malfunction.
Low sounds will not emanate; vocals are distorted.
When connecting a Pioneer passive subwoofer S-SLW500 or
HVT speaker (S-HV500-LR, etc.), set the X.Over of this receiver
to 200Hz (see X.Over on page 37).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the
noise disappears.
No sound is output or a noise is output when software with
DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-S500-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-S500-K in the language / languages: English as an attachment in your email.

The manual is 6,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-S500-K

Pioneer VSX-S500-K Quick start guide - English, German - 32 pages

Pioneer VSX-S500-K User Manual - German - 56 pages

Pioneer VSX-S500-K Quick start guide - Dutch - 32 pages

Pioneer VSX-S500-K User Manual - Dutch - 56 pages

Pioneer VSX-S500-K User Manual - Dutch - 56 pages

Pioneer VSX-S500-K User Manual - Danish - 150 pages

Pioneer VSX-S500-K Quick start guide - French - 32 pages

Pioneer VSX-S500-K User Manual - French - 60 pages

Pioneer VSX-S500-K Quick start guide - Italian - 32 pages

Pioneer VSX-S500-K User Manual - Italian - 56 pages

Pioneer VSX-S500-K User Manual - Swedish - 150 pages

Pioneer VSX-S500-K Quick start guide - Spanish - 32 pages

Pioneer VSX-S500-K User Manual - Spanish - 56 pages

Pioneer VSX-S500-K User Manual - Norwegian, Finnish - 150 pages

Pioneer VSX-S500-K User Manual - Finnish - 150 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info