536846
24
Zoom out
Zoom in
Previous page
1/133
Next page
Basic Setup
3
3
24
58
7
4
Press
HOME MENU
at any time to exit the Home
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
The screensaver automatically starts after three
minutes of inactivity.
6
Select ‘Auto MCACC’ from the Home Menu, then press
ENTER
.
Mic In! blinks when the microphone is not connected
to MCACC SETUP MIC jack.
Try to be as quiet as possible after pressing
ENTER
. The
system outputs a series of test tones to establish the
ambient noise level.
7
Follow the instructions on-screen.
Make sure the microphone is connected.
Make sure the subwoofer is on and the volume is
turned up.
When using surround back speakers, turn on the
power to the amplifier to which the surround back
speakers are connected, and adjust the sound level to
the desired level (VSX-S510 only).
8
Wait for the test tones to finish.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
For correct speaker settings, do not adjust the volume
during the test tones.
9
Confirm the speaker configuration.
The configuration shown on-screen should reflect the
actual speakers you have.
With error messages (such as Too much ambient
noise) select RETRY after checking for ambient noise
(see Other problems when using the Auto MCACC
setup below).
If the speaker configuration displayed isn’t correct, use
/
to select the speaker and
/
to change the
setting. When you’re finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn’t fix the problem,
turn off the power and check the speaker connections.
10
Make sure ‘OK’ is selected, then press
ENTER
.
If the screen in step 9 is left untouched for 10 seconds
and
ENTER
is not pressed in step 10, the Auto MCACC
setup will start automatically as shown.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, X.Over, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 1 to 3 minutes.
11
The Auto MCACC setup has finished! You return to the
Home Menu.
The settings made in the Auto MCACC setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
Home Menu (starting on page 51
).
Note
Depending on the characteristics of your room, sometimes
identical speakers with cone sizes of around 12 cm will end
up with different size settings. You can correct the setting
manually using the Speaker Setting
on page 51.
The subwoofer distance setting may be farther than the
actual distance from the listening position. This setting
should be accurate (taking delay and room characteristics
into account) and generally does not need to be changed.
Home Menu
1
. Auto MCACC
2
. Manual SP Setup
3
. Input Assign
4. Auto Power Down
5. HDMI Setup
6. Network Standby
7. MHL Setup
8. Speaker System
9. OSD Setup
Home Menu
1
. Auto MCACC
2
. Manual SP Setup
3
. Input Assign
4. Auto Power Down
5. HDMI Setup
VSX-S510 VSX-S310
1
. Auto MCACC
Now Analyzing
Environment Check
Ambient Noise
Speaker YES/NO
Return
1
. Auto MCACC
Check
Return
10:Next
Front
Center
Surr
Surr. Back
Subwoofer
[ YES ]
[ YES ]
[ YES ]
[YESx2]
[ YES ]
1
. Auto MCACC
Check
OK
Return
10:Next
Front
Center
Surr
Subwoofer
[ YES ]
[ YES ]
[ YES ]
[ YES ]
OK
VSX-S510 VSX-S310
1
. Auto MCACC
Now Analyzing
Surround Analyzing
Speaker System
X.Over
Speaker Distance
Channel Level
Acoustic Cal EQ
Return
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-S310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-S310 in the language / languages: English as an attachment in your email.

The manual is 16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-S310

Pioneer VSX-S310 Quick start guide - English, German - 60 pages

Pioneer VSX-S310 User Manual - German - 66 pages

Pioneer VSX-S310 Quick start guide - Dutch - 60 pages

Pioneer VSX-S310 User Manual - Dutch - 65 pages

Pioneer VSX-S310 User Manual - Danish - 188 pages

Pioneer VSX-S310 Quick start guide - French - 60 pages

Pioneer VSX-S310 User Manual - French - 67 pages

Pioneer VSX-S310 Quick start guide - Italian - 60 pages

Pioneer VSX-S310 User Manual - Italian - 65 pages

Pioneer VSX-S310 User Manual - Swedish - 188 pages

Pioneer VSX-S310 Quick start guide - Spanish - 60 pages

Pioneer VSX-S310 User Manual - Spanish - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info