Manual Pioneer VSX-LX304 (page 148 of 180) (English)

699657

148

Zoom out

Zoom in

1/180

148

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure

the test tones emitted by the speakers, then the unit automatically sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also reduces the eect of the standing

wave in accordance with the viewing environment and automatically adjusts the

equalizers for the speakers and enables correction of distortion caused by the

acoustic environment of the room.

• Calibration takes between 3 and 12 minutes to be completed. The speakers

emit the test tone at high volume during measurement, so be careful of your

surroundings. Keep the room as quiet as possible during measurement.

• If you have connected a subwoofer, check the power and volume of the

subwoofer. Set the subwoofer volume to more than halfway.

• If the power of this unit suddenly turns o, the wires in the speaker cables

may have touch the rear panel or other wires and tripped the protection circuit.

Twist the wires again properly and make sure they do not stick out of the

speaker terminals when connecting.

1. Select the connected speaker conguration.

Height 1 Speaker

Height 2 Speaker

Top Middle

Zone 2 Preout

Zone 2

7.1.2 ch

Zone Speaker

The image on the screen changes as you choose the number of channels in

"Speaker Channels", so refer to it when performing the settings.

2. Place the supplied speaker setup microphone in the listening position, and

connect to the SETUP MIC jack on the main unit.

SETUP MIC

When putting the speaker setup microphone on a tripod, refer to the illustration

when putting it in place.

3. Conrm a test tone is output from the subwoofer and press ENTER.

4. Press ENTER. Then, test tones are output from each speaker, and the

connected speakers and the noise in the surrounding environment are

automatically measured.

5. The measurement results in step 4 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

• When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

• When it cannot be resolved by performing the re-measurement, conrm

if the speakers are connected correctly. If there is any problem with the

speaker connection, perform the connection after disconnecting the power

cord.

6. Once the measurement is completed, it is possible to perform the

measurement in 8 additional listening positions. To perform the measurement,

select "Next" and press ENTER, then follow the instructions. To not perform

the measurement, select "Finish (Calculate)" and press ENTER.

• After each listening position is detected, select "Finish (Calculate)" and

press ENTER to complete the detection process.

7. Disconnect the speaker setup microphone.

Can I connect the Sonos arc to the elite Av vsx-lx 304 instead of of my LG Oled. Right now everything I have is connected to my Elite. The Elite is connected to the LG earc output.I use my internet provider (spectrum) set top box remote to control everything I would like to keep it that way. Submitted on 25-9-2021 at 19:51
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-LX304 in the language / languages: English as an attachment in your email.

The manual is 10,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-LX304

Pioneer VSX-LX304 User Manual - German - 185 pages

Pioneer VSX-LX304 User Manual - Dutch - 182 pages

Pioneer VSX-LX304 User Manual - French - 181 pages

Pioneer VSX-LX304 User Manual - Italian - 180 pages

Pioneer VSX-LX304 User Manual - Swedish - 180 pages

Pioneer VSX-LX304 User Manual - Spanish - 180 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-LX304 Manual

Product: