574223
58
Zoom out
Zoom in
Previous page
1/71
Next page
Controlling the rest of your system
10
58
En
4 Use
and
to select the first letter of
the brand name of your component then
press ENTER.
This should be the manufacturer’s name (for
example,
P
for Pioneer).
5 Use
and
to select the manufac-
turer’s name from the list then press
ENTER
6 Use
and
to select the proper code
from the list, then try using this remote
control with your component.
The code should start with the component
type (for example,
DVD_5305
). If there is
more than one, start with the first one.
To try out the remote control, switch the
component on or off (into standby) by
pressing
SOURCE
. If it doesn’t seem to
work, select the next code from the list (if
there is one).
VSX-D914 model only –
If you can’t find or
properly enter a preset code, you can still
teach the remote individual commands
from another remote control (see
Programming signals from other remote
controls
below).
7 If your component is controlled
successfully, press ENTER to confirm.
The remote LCD display shows
OK
.
Programming signals from
other remote controls
VSX-D914 model only
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals
from the remote control of another compo-
nent. This can also be used to program addi-
tional operations (buttons not covered in the
presets) after assigning a preset code.
1 While pressing the RECEIVER button,
press and hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button for
the component you want to control.
The LCD on the remote displays the compo-
nent you want to control.
You can’t assign the
RECEIVER
button.
3 Use
and
to select LEARN then
press ENTER.
PRES KEY
and the
LEARN
icon show in the
LCD display.
To exit or cancel press
RECEIVER
.
4 Point the two remote controls
towards each other then press the button
that will be doing the learning on this
receiver’s remote control.
PRES KEY
and the
LEARN
icon start flashing
to indicate the remote is ready to accept a
signal.
The remote controls should be 1–2 inches
apart.
5 Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s
remote control.
For example, if you want to learn the playback
control signal, press
. The LCD display will
show
OK
if the operation has been learned.
If for some reasons the operation hasn’t been
learned the LCD will display
ERROR
briefly
and then display
PRES KEY
again. If this
happens, keep pressing the (teaching) button
as you vary the distance between the two
remotes, until the LCD display shows
OK
.
1 – 2 inches
+
10
INPUT ATT FL DIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
SETUP
ENTER
TV CONTROL
RECEIVER CONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TV CONT
CD
TUNE
TUNE
ST ST
STANDRAD
LEVEL EFFECT
TEST TONE
CH SELECT
ADV. SURR STEREO SLEEP
INPUT
SELECT
TV CH
DTV ON/OFF
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
DTV INFOREC MU TE
TV VOL
CD-R/TAPE
TUNER RECEIVER
ENTER
REC STOP
HDD
CH
CH
DVD
D.ACCESS
TOP MENU
DTV MENU
CLASS
MENU
BAND
RETURN
GUIDE
T.EDIT
MCACC
SETUP
RECEIVER
VSX_D912.book.fm 58 ページ 2003年12月5日 金曜日 午前9時43分
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-D914 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-D914 in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info