574207
28
Zoom out
Zoom in
Previous page
1/48
Next page
28
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
LOUDNESS FUNCTION MUTING
RECEIVER
D.ACCESS CHANNEL
ATT
VOL
MENU
TOP
MENU
VOL
CH
2
DSP MODE
MIDNIGHT
5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL
EFFECT
ENTER
ENTER
FQ
FQ
ST ST
FL
DIMMER
REMOTE
SETUP
MASTER
VOLUME
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
TV CONTROL
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER
TUNER
TV CONT
Î
1234
1 ¡ 4 ¢
7 8 3
5678
90
SOURCE CLASS MPX BAND
Switching ANALOG/DIGITAL Signal Input
Set this switch to tell the receiver whether you’re using a component that is hooked up digitally or in an analog
manner. If you have no components connected digitally the switch wonb’t allow you to select digital.
1
Press SIGNAL SELECT to select the input
signal corresponding to the source
component.
Each press switches between ANALOG and DIGITAL signal
selection.
2
While SIGNAL SELECT is set to DIGITAL,
DIGITAL lights when a Dolby Digital signal is
input, DTS lights when a DTS signal is input.
SIGNAL
SELECT
SIGNAL SELECT is fixed in the “ANALOG” position for components
not assigned to one of the two digital input jacks.
This receiver can only play back Dolby Digital, PCM (32kHz, 44kHz, and
48kHz), DTS, digital signal formats. With digital signal formats other
than these, set SIGNAL SELECT to “ANALOG”.
When an LD or CD player compatible with DTS is played back with
SIGNAL SELECT set in “ANALOG”, digital noise is output caused by
playing back the DTS directly (no decoding). To prevent noise, you
need to make digital connections (Refer to page 11) and set SIGNAL
SELECT to “DIGITAL”.
Some DVD players don’t output DTS signals. For more details, refer to
the instruction manual supplied with your DVD player.
Audio from a karaoke microphone and some LDs are analog so set the
SIGNAL SELECT to “ANALOG” in these cases.
For analog LDs and karaoke microphones, set the switch to
“ANALOG.”
Sound Modes
memo
AT T
CH
2
DSP MODE
MIDNIGHT
5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL
EFFECT
ENTER
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER
TUNER
TV CONT
1234
5678
90
SIGNAL SELECT
1
Turn on the power of the playback
component.
2
Turn on the power of the receiver.
Be sure that the standby indicator turns off on
the front panel.
3
Press MULTI CONTROL buttons or the
FUNCTION button to select the source you
want to playback.
If the DIRECT FUNCTION is OFF you have to use the FUNCTION
button to select the source (see p.22).
4
If necessary, press SIGNAL SELECT to select the
input signal corresponding to the source
component (as above).
5
Start playback of the component you selected
in step 1.
Playing a Source
3
2
3
4
SIGNAL
SELECT
ANALOG
SIGNAL
SELECT
ANALOG
DIGITAL
SIGNAL
SELECT
ANALOG
DIGITAL
2DIGITAL
SIGNAL
SELECT
ANALOG
DIGITAL
DTS
Each press switches between ANALOG
and DIGITAL signal selection.
When a Dolby Digital
signal is input.
When a DTS
signal is input.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-D309 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-D309 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info