574069
109
Zoom out
Zoom in
Previous page
1/120
Next page
Techno Tidbits and Problem-solving
109
En
EXPERT
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the
other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the
checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
i.LINK indicator flashes, but no
sound is output.
An output signal is not produced from
the i.LINK connector on the source
player.
The selected component is not compati-
ble with i.LINK Audio.
The selected component does not corre-
spond to DTCP.
Refer to the manual that came with the
source player.
Refer to the manual that came with the
source player.
The unit corresponds to DTCP. Refer to
the manual for the selected compo-
nent.
i.LINK indicator does not light
up even when an i.LINK-
equipped component is
selected.
The i.LINK cable is dislocated.
The i.LINK cable is too long.
The selected component does not corre-
spond to the i.LINK AUDIO format.
The component between the unit and
the source player is turned off.
Check all connections.
Use a cable less than 3.5m long.
Refer to the manual for the selected
component.
When the source player is turned off or
in the standby mode, the output signal
is not produced. Refer to the manual
for the selected component.
The program format
indicators don’t disappear
when SACD/DVD-A playback
stops.
The program format indicators remain lit
until another format source is input.
PQLS OFF or PQLS ON is
displayed temporarily and the
sound output is discontinued.
During playback through an i.LINK con-
nection, if you change the settings for
other i.LINK components, the sound will
be discontinued momentarily.
After upgrading a component
and then connecting it
through an i.LINK connection,
the name for the component
is not displayed and the
component is not selected.
Depending on the upgrade process, cer-
tain components may not be recognized
by the unit.
Initialized all the information stored in
the unit in the order as follows:
1. When the unit is in the standby
mode, press and hold STEREO/DIRECT
and then press STANDBY/ON.
2. When “DB CLEAR?” is displayed,
press MULTI CH IN.
3. When “DB CLEAR OK?” is displayed,
press ACOUSTIC EQ.
4. Make sure “DB CLEAR SET” is
displayed to end initialization.
5. If “DB ERROR” is displayed, step
through the procedure again.
The power does not turn on The power plug is disconnected.
The protection circuit may have been
activated.
Connect the power plug to the wall out-
let.
Disconnect the power plug from the
outlet, and insert again.
Power
i.LINK interface
Cause
Remedy
Symptom
VSX-AX5i.book Page 109 Friday, May 23, 2003 6:33 PM
109


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-AX5i-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-AX5i-S in the language / languages: English as an attachment in your email.

The manual is 12,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-AX5i-S

Pioneer VSX-AX5i-S User Manual - German - 116 pages

Pioneer VSX-AX5i-S User Manual - Dutch - 116 pages

Pioneer VSX-AX5i-S User Manual - French - 116 pages

Pioneer VSX-AX5i-S User Manual - Italian - 116 pages

Pioneer VSX-AX5i-S User Manual - Turkish - 116 pages

Pioneer VSX-AX5i-S User Manual - Spanish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info