699661
133
Zoom out
Zoom in
Previous page
1/153
Next page
133
Front Panel Rear Panel Remote
Contents
Connections
Playback
Setup
If you have terminated the Initial Setup halfway, turn this unit to standby mode.
Then turning the power on again can display the Initial Setup again.
The Initial Setup appears on the screen each time the power is turned on
unless the Initial Set up is completed or "Never Show Again" is selected on the
rst screen.
To perform the Initial Setup again after the setting is completed, press ,
select "System Setup" - "Miscellaneous" - "Initial Setup", and press ENTER.
1. Speaker Setup
Select the connected speaker conguration.
Note that the image on the screen changes each time you select the number of
channels in "Speaker Channels".
Speaker Setup
Speaker Impedance 6 ohms or above
2. Full Auto MCACC
Place the supplied speaker setup microphone at the listening position. The unit
automatically measures the test tones output from each speaker, and sets the
optimum volume level for each speaker, the crossover frequencies, and the
distance from the listening position. This also automatically adjusts the equalizers
for the speakers, and enables correction of sound distortion caused by the
acoustic environment of the room.
It takes between 3 and 12 minutes for calibration to be completed. Each
speaker outputs the test tone at high volume during measurement, so be
careful of your surroundings. Also, keep the room as quiet as possible during
measurement.
If you connect a subwoofer, check the power and volume of the subwoofer.
Set the subwoofer volume to more than half.
If the power of this unit suddenly turns o, the wires in the speaker cables
have touched the rear panel or other wires, and the protection circuit is
working. Twist the wires again securely, and make sure they do not stick out of
the speaker terminals when connecting.
1. Place the supplied speaker setup microphone at the listening position, and
connect it to the SETUP MIC jack on the main unit.
SETUP MIC
When placing the speaker setup microphone on a tripod, refer to the
illustration.
2. Conrm a test tone is output from the subwoofer and press ENTER.
3. Press ENTER. Then, test tones are output from each speaker, and the
connected speakers and the noise in the surrounding environment are
automatically measured.
4. The measurement results in step 3 are displayed. Select "Next", and press
ENTER. The test tones are output again. Then, the unit automatically sets the
optimum volume level, crossover frequency, etc.
5. When the measurement is completed, the measurement results are displayed.
You can check each setting using the cursors
/ . Select "Save" and press
ENTER to save the settings.
6. Disconnect the speaker setup microphone.
3. Multi Zone Sound Check
Output test tones to ZONE 2 to enjoy audio in a separate room (ZONE 2) in
addition to the main room.
133


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-934 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-934 in the language / languages: English as an attachment in your email.

The manual is 7,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-934

Pioneer VSX-934 Additional guide - English - 26 pages

Pioneer VSX-934 Quick start guide - English - 2 pages

Pioneer VSX-934 Additional guide - German - 26 pages

Pioneer VSX-934 User Manual - German - 154 pages

Pioneer VSX-934 Additional guide - Dutch - 26 pages

Pioneer VSX-934 User Manual - Dutch - 153 pages

Pioneer VSX-934 Additional guide - French - 26 pages

Pioneer VSX-934 User Manual - French - 155 pages

Pioneer VSX-934 Additional guide - Italian - 26 pages

Pioneer VSX-934 User Manual - Italian - 154 pages

Pioneer VSX-934 Additional guide - Swedish - 26 pages

Pioneer VSX-934 User Manual - Swedish - 153 pages

Pioneer VSX-934 Additional guide - Spanish - 26 pages

Pioneer VSX-934 User Manual - Spanish - 155 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info