586463
117
Zoom out
Zoom in
Previous page
1/142
Next page
117
FAQ
14
Professional Calibration EQ graphical output
Symptom Remedy
The reverb characteristics graph
after EQ calibration does not appear
entirely flat.
There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
in the Auto MCACC Setup) due to adjustments made to compensate for room character-
istics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.
The graph may appear to have shifted vertically when comparing before and after mea-
surements.
EQ adjustments made using the
Manual MCACC setup do not appear
to change the reverb characteristics
graph after EQ calibration.
Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the reverb characteristics graph after EQ calibration. However, these
adjustments are taken into account by the filters dedicated to overall system calibration.
Lower frequency response curves do
not seem to have been calibrated for
SMALL speakers.
Low frequencies used in bass management (the subwoofer channel) will not change for
speakers that have been specified as SMALL in the configuration, or do not output these
frequencies.
Calibration is performed, but due to your speakers’ low frequency limitations, no measur-
able sound is output for display.
Display
Symptom Remedy
The display is dark or off. Press DIMMER repeatedly to select a different brightness.
The OSD screen is not displayed. The on-screen display is not displayed unless this receiver’s HDMI OUT terminal is con-
nected to the TV by HDMI cable. If the TV does not support HDMI, watch this receiver’s
front panel display when performing operations and making settings.
When the input is a 3D signal, OSD cannot be displayed.
Even through the input is switched,
DIGITAL does not light.
Check the digital connections and make sure that the digital inputs are assigned cor-
rectly (see The Input Setup menu on page 59 ).
When playing Dolby Digital or DTS
sources, the receiver’s format indica-
tors do not light.
Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.
When AUTO is set with the Auto
Phase Control Plus feature, ‘---’ is
displayed.
There are disks that cannot be adjusted using AUTO. Please adjust manually (page 85 ).
Remote control
Symptom Remedy
Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the
main unit (see Operating multiple receivers on page 93 ).
Check whether the receiver’s remote control mode is properly set (see Remote Control
Mode Setup on page 110 ).
Try replacing the batteries in the remote control (see Loading the batteries on page 10 ).
Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel
(see Operating range of remote control unit on page 10 ).
Check that there are no obstacles between the receiver and the remote control.
Make sure that there is no fluorescent or other strong light shining on to the remote
sensor.
Excluding VSX-830: Other compo-
nents can’t be operated with the
system remote.
If the battery ran down, the preset codes may have been cleared. Re-enter the preset
codes.
The preset code may be incorrect. Redo the procedure for entering preset codes.
When commands from the remote control units of other devices are registered using the
learning function, in some cases they may not be learned properly. In this case, register
the commands again using the learning function (see page 94 ). If they still do not work,
they may be in a special format that cannot be registered on this receiver’s remote con-
trol. Operate the device using another remote control.
 
117


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-930 K-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-930 K-S in the language / languages: English as an attachment in your email.

The manual is 20,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-930 K-S

Pioneer VSX-930 K-S User Manual - German - 146 pages

Pioneer VSX-930 K-S User Manual - Dutch - 146 pages

Pioneer VSX-930 K-S User Manual - French - 145 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info